The above is a brief introduction to the effect and form of shaft seal of submersible slurry pump. Users can choose the appropriate shaft seal type according to their actual needs.　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. It is normal to use the equipment for a long time, for example, when the submersible slurry pump is used at ordinary times, air holes usually appearKanabad,　　The equipment of this series of sewage pumps can be fixed or mobile. When the fixed active equipment is selected, and its connection shall be parallel to the pump outlet) two eyebolts or lifting plates to lift the electric pump up and down. Evenly and slowly along the guide rail　　The purpose is to avoid water leakage of the pump,KanabadPipeline pump body, but the water seal may be damaged due to faults after being used for a period of time. Let&#;s learn how to replace the water seal.Qibray　　 Then unscrew the nut at the front end of the pump shaft, remove the cover plate, and press out the middle impeller and water seal.　　 It may also be because the pump&#;s liquid supply pipe is blocked by other substances during normal use.　　The higher the specific speed of submersible slurry pump,KanabadSelf priming slurry pump wholesale, the smaller the allowable cutting amount of impeller diameter. In addition to the sealing effect, the auxiliary impeller of the submersible slurry pump can also reduce the axial force.

　　Discount. In order to meet the needs of industrial production and make the submersible pump to achieve the ideal use effect, accurate and reasonable selection is very important. In order to select the pump reasonably and correctly, the following aspects need to be considered: Selection of shaft seal form: shaft seal of submersible slurry pump　　Try to select the pump with appropriate lift.　　 there is also a simple method to measure the vibration frequency of the pump by vibration method. However, when using one method, there may be some errors in the measurement results. When many equipment are used, there are other vibration sources that will affect the measurement results. Therefore,　　If there is a standby pump, it is recommended that the two pumps be used in turn. When the equipment is in use, it can pretend that a filter screen plays the role of filtration, so as to avoid a lot of impurities entering the equipment and causing pump jamming.　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.　　The above is the reason for the insufficient liquid supply of the water pump when it is in use, as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in use

　　What is the cause of pump overload.Development Curriculum,　　The structure of the submersible slurry pump will be more intuitive. First,KanabadSmall deep well pump, the equipment will use centrifugal force to drive the liquid from the impeller to the outer edge and obtain energy, and then leave the edge of the impeller at a higher speed　　The sub bearing and cylindrical roller bearing can bear the maximum axial and radial loads of the pump. The bearing is lubricated with grease. The two ends of the bearing body are provided with sealing end caps, labyrinth sleeves and labyrinth rings, which can effectively prevent dirt such as mineral slurry from entering the bearing, ensure the safe operation of the bearing and have a high service life.　　How to avoid this situation when the equipment is in use.Kanabad　　After understanding the working principle of the submersible slurry pump, we will also know that those parts are prone to wear during normal use. In this way, we can carry out targeted anti-corrosion and wear-resistant treatment on these parts during optimization, so as to improve the integrity of the equipment and　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point.　　The type selection planning of submersible slurry pump has a great impact on its service life and operation stability. A scientific and reasonable type selection plan will affect whether the slurry pump can achieve efficient operation. The operating power of the slurry pump is very high and the loss is small. Service life of flow passage parts of pump