the square tube can be well protected by electrolysis. These are simple ways to prolong the service life of the square tube

After chemical pickling, We only need to treat according to these,GondomaGalvanized steel pipe, cold galvanizing coating is mainly carried out according to the electrochemical principle. Therefore, it is necessary to ensure the sufficient of zinc powder and steel resulting in electrode potential difference, so the steel surface treatment requirements are very high.Brinell hardness (HB), Rockwell hardness (HRC) and Vickers hardness (HV) are commonly used.Gondoma,Whether the bottom is galvanized or painted; For paint, it is recommended to match: epoxy zinc rich um + epoxy micaceous iron intermediate paint um + polyurethane finish paint um. In this way, according to the standard of iso, you can protect the indoor and outdoor environment for years, which is not a big problem.The principle is similar to that of the plate rolling machine. The bending machine can determine a circle. Adjust the height to adjust the curvature.Su Mei,C. special performance steel: (a) stainless and acid resistant steel; (b) Heat resistant steel; (c) Electric heating alloy steel; (d) Electrical steel; (e) High manganese wear resistant steel.Reinforcing phases such as reinforcing particles, short fibers and whiskers can be added to the solder to form composites.Generally, chemical and electrolytic methods are used

A. square tube structural steel: (a) high quality carbon structural steel; (b) Alloy structural steel; (c) Spring steel; (d) Easy cutting steel; (e) Bearing steel; (f) High quality structural steel for specific purposes.From the perspective of production, we should give full play to the productivity of production equipment and reduce the consumption of fuel and equipment on the basis of meeting the size and performance requirements of qb square tube. Therefore, the temperature of no open forging and final forging is a comprehensive technical and economic problem. If qualified qb square tubes can be obtained in the temperature range of the vehicle, reasonable process procedures should be selected from an economic point of view. Obviously, the higher the temperature, the easier the forging and the higher the productivity, but the greater the fuel consumption and the loss of the heating furnace; We should consider these two aspects and make a reasonable choice.Section shape classification of large-diameter qb square tube square tube is classified according to section shape: simple section square tube & mdash& mdash; Square tube, rectangular tube and complex section square tube & mdash& mdash; Flower shaped square pipe, open square pipe, corrugated square pipe, large-diameter qb square pipe surface treatment classification square pipe is divided according to surface treatment: hot-dip galvanized square pipe, electro galvanized square pipe, oil coated square pipe, acid pickling square pipe, large-diameter qb square pipe purpose classification square pipe is classified according to purpose & mdash& mdash; Square tubes for decoration, machine tool equipment, machinery industry, chemical industry, steel structure, shipbuilding, automobile, steel beam and column, special purpose, large-diameter qb square tube wall thickness classification, large diameter qb square pipe and thin-wall large diameter qb square pipe rectangular pipe are the names of square pipe and QB square pipe, that is steel pipe with equal side length. It is made of rolled strip steel after process treatment. Generally, the strip steel is unpacked, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Usually pieces per bag. Qb square pipe also known as square and rectangular cold-formed hollow section steel, is referred to as square pipe and rectangular pipe, code f and j respectively. The allowable deviation of wall thickness of qb square pipe shall not exceed plus or minus % of nominal wall thickness when the wall thickness is not greater than mm, plus or minus % of wall thickness when the wall thickness is greater than mm,After spraying (throwing) derusting, it can not only expand the physical adsorption on the pipe surface, but also enhance the mechanical adhesion between the layer and the pipe surface. Therefore, spray (throwing) derusting is an ideal derusting method for pipelines. Generally speaking, shot blasting (sand) is mainly used for the inner surface treatment of the pipe, and shot blasting (sand) is mainly used for the outer surface treatment of the pipe. Several problems should be paid attention to in derusting by spraying (throwing).Among them, qb square tube is divided into: (a) by process & mdash& mdash; Arc welded square pipe, resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe (b) are divided by weld & mdash& mdash; Straight seam welded square pipe,GondomaGalvanized JDG pipe,GondomaQuotation of galvanized square pipe, spiral weldingThe disadvantage of empty bending is that during synchronous empty bending at the upper and side, due to the pressure generated by the upper roll and the lower roll at the same time, the forming force is easy to exceed the critical point. All kinds of square tubes, square rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have formal qualifications. Welcome to telephone inquiry and sincerely invite cooperation! It will cause edge instability and concave, and will also affect the stable operation of the unit and forming quality. This is also the different characteristics of qb square tube and round tube empty bending.

Tool derusting mainly uses tools such as steel wire brush to polish the surface of square pipe, which can remove loose or oxidized scale, rust, welding slag, etc. The derusting of manual tools can reach grade SA and that of power tools can reach grade SA. If the square pipe surface is firmly attached with iron oxide scale, the derusting effect of tools is not ideal and can not reach the anchor depth required by construction.High quality brand,Empty bending empty bending is the bending moment formed in one direction between the outer roll and the outer wall of the tube blank to bend the strip. Empty bending will compress the bending line, the compression effect will lengthen the bending line longitudinally, and the metal at the bending will accumulate and thicken, which is the compression thickening effect of empty bending.High temperature diffusion heat treatment of ingot can improve the composition heterogeneity of ingot and improve the transverse performance of square tube.Improve the positioning and pre bending steps, if necessary, to ensure that the web hunting problem does not occur when pressing parts. Change the shape of the surface pressure of the material to ensure the quality of the parts and avoid the non movement of the surface shape of the roll gap, resulting in uneven walking feeding.Gondoma,Large diameter qb square tube production standard classification square tube is divided according to production standard: national standard square tube Japanese standard square tube, British standard square tube, American standard square tube, European standard square tube and non-standard square tube.Derusting: This is an important process for galvanized square pipes and components before coating, and it is the key to the quality of galvanized square pipes. Thorough derusting can improve the adhesion of antirust paint and prolong the service life of galvanized square pipe.With the progress of the times and the faster and faster economic development