Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.Ensure good power supply at the installation site, install a separate distribution box, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .Zhuozhou,Pay attention to heat dissipation when the motor works in a hot environment.Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, this will hide the moisture. Therefore, the outer edge of the wheel hub, the door, the corner of the bottom of the trunk the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.Almada,Are the water cooling and air cooling of the hydraulic station the same?The load of this series of products is divided into . to . tons, and can also be customized according to user requirements, with a load of up to tons.The contact opening and closing of the travel switch of each safety device must be reliable, and the contact arc crater should be polished in time.

Uses: The scissor-type fixed lifting platform is mostly used for the transportation of goods between the height differences of the production line, the loading and unloading of materials, the adjustment of the working height during the assembly of the workpiece, the feeding of the installed machine at a high place, the lifting of parts during the assembly of large equipment, and the storage and unloading place and Forklifts and other handling vehicles are used for fast loading and unloading of goods, car lifting, fixed three-dimensional parking and other places.How to maintain the elevator correctly and replace the hydraulic oil of the elevator regularly: the hydraulic oil used in the elevator is divided into winter and summer. It is not noticed until the hydraulic cylinder of the elevator is working abnormally.The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same and there is a big difference. Long-term promotion of freight elevator factories and other, mutual benefit and win-win. If you choose the wrong supplier Long-term cooperation, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.Finance Department,Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding, the short-circuit current is much larger than the normal operating current which increases the copper loss of the winding, causing the winding to overheat and even burn out.Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?

It is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy, the clothing will repeatedly slap the car paint, especially if the car blows sand on the clothes, it will draw many fine scratches on it. Because it will turn black over time. In addition, when the wind does not directly spray powder or clean the sand on the mechanism, but it should be washed with water,ZhuozhouA cargo elevator needs to, and prevent the sand particles on the paint surface from being scratched by the vacuum cleaner.Equipment maintenance,The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches,ZhuozhouIndustrial cargo elevators, it will cause the winding and core to overheat, and in severe cases, the winding will be burned.Guide rail hydraulic freight elevator is a kind of hydraulic lifting mechanical equipment. It is used for the transportation of goods between the floors of industrial plants with more than one floor, restaurants and hotels. The low height is suitable for a variety of working conditions, no upper lifting point is required, and the structure is diversified (single-column, double-column, four-column guide rail). The equipment runs smoothly, the operation is simple, and the goods are transported up and down stably.Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.Zhuozhou,The contact opening and closing of the travel switch of each safety device must be reliable, and the contact arc crater should be polished in time.It is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy, especially if the car blows sand on the clothes, it will draw many fine scratches on it. Because it will turn black over time. In addition, when the wind does not directly spray powder or clean the sand on the mechanism, but it should be washed with water, and prevent the sand particles on the paint surface from being scratched by the vacuum cleaner.Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles, containers, mold manufacturing, wood processing, chemical filling, etc. to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls, rollers, Turntable,Zhuozhou4-ton cargo elevator, steering, tilting, telescopic), with various methods (separate, explosion-proof), with the characteristics of stable and accurate lifting, large load capacity, etc., effectively solving the difficulties of various lifting operations in industrial enterprises, so that Production operations freely. The professional elevator factory has advanced technology, strict testing, more affordable prices, welcome to consult.