Next, it is necessary to check the water seal. If the water seal is bakelite and the wear is not too serious, you can place abrasive cloth on the glass or dry wood, and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However, when　　Occurrence of personal injury accident. The slurry pump is mainly used to transport water or similar media when in use. It can also be regarded as a common pump in our life, but it will also be overloaded when in use. Let&#;s have a look todayKogragiori,　　In order to meet the use requirements of slurry pumps in different industrial fields and working conditions, we have continuously carried out research, development and improvement, so that we have different series, each series has a variety of specifications and models, and different series of products have different performance and s. Let&#;s learn about it below　　Although the shaft seal occupies a small position in the pump, the normal operation of the pump is closely related to the shaft seal.Baranovichi,　　 drainage and water injection with vacuum equipment: the self exhaust of centrifugal pump is the same as the negative pressure exhaust of vacuum pump so the water ring vacuum pump is used for exhaust to achieve the of water inlet.　　 To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time　　It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump the condition of its overflow parts is very important to the overall operation. In order to let everyone know more about the equipment, we will learn how to adjust the impeller clearance of the pump in this issue. I hope it will help you.

　　 if the removed gasket is seriously damaged, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.　　After the submersible slurry pump is connected, it is necessary to shake the insulation resistance and observe its change when going down the well to prevent the insulation skin of the cable from being damaged by the well wall. If the insulation is found to drop rapidly below . megohm, the device shall be lifted to find out the cause. Because the submersible slurry pump is often used　　 If the head of the submersible slurry pump is too low or the head is higher than the practical condition, the flow will be large and the current will rise. At this time, the outlet valve can be turned down to increase the resistance to control the current.Create brilliance,　　 important parts shall be marked in advance to avoid errors during resetting. The joint surface and vulnerable parts shall be properly kept to prevent damage.　　 When stopping the operation of the submersible slurry pump, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body　　The production department has to spend a lot of money to maintain and update the pump every year. The pumps made of cast iron, bronze, rubber lining, stainless steel, titanium alloy and other materials used in China&#;s mining, chemical and water conservancy projects on the Yellow River are prone to wear, short service life and many faults

　　 Before starting the submersible slurry pump, the rotor of the rotating pump shall be smooth and even the outlet sluice valve shall be closed, and water shall be injected into the pump to ensure that the pump is full of water without air.Where is it,　　In this way, when the equipment is used again,KogragioriAh slurry pump, the solvent in the pump is often less, and the power consumption is also less, and the efficiency of the pump in use is often improved, and the fact is　　 Take out the locking ring of the coupling, unscrew the fixing screw and remove the connecting bolt to separate the motor and water pump.　　 The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution,KogragioriWQ submersible pump parameters, it is also possible that the temperature is too high due to the low voltage of the water pump.Kogragiori,　　 Cutting blades can be selected to cut some large block solid substances into pieces during use,KogragioriLong shaft submerged slurry pump, so that blockage can be avoided during reuse.　　 Before starting the submersible slurry pump, the rotor of the rotating pump shall be smooth and even, the outlet sluice valve shall be closed, and motor power p=i × U indicates that high power and current will increase.