Moreover, because the length of the long shaft is generally fixed, it is often troublesome to install it. Therefore, when it is used later,UtsunomiyaSubmersible non clogging slurry pump, the place where it operates will also be limited. If the equipment will　　 The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked,Utsunomiya,　　 the insulation resistance between the shaking cable and the submersible slurry pump shall not be less than megohm.　　Rate.Kenya,　　The structure of the submersible slurry pump will be more intuitive. First, the equipment will use centrifugal force to drive the liquid from the impeller to the outer edge and obtain energy, sewage submersible pump and seawater submersible pump.　　When using the submersible slurry pump, in the market, for example, the sweeping pump, some of which have a depth of more than meters, it is not suitable to use a vertical slurry pump under such a working condition, but it is extremely easy to use a submersible slurry pump.　　 Store in a well ventilated and dry place. If it is stored during idle period, the pump shall be slowly lifted from the water source and drained (especially in cold winter).　　 the front and rear bearing glands are equipped with oil seals, which are padded with green paper or asbestos. There is a gap of .- mm between the rear gland and the bearing.High value,　　 To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time　　In fact, the pumps I am going to talk about here have a wide range of uses. Pumps are required for both civil and military purposes, as well as for advanced technologies, especially in the mining, metallurgical and other industrial sectors. It is a widely used general mechanical equipment. Most pumps are corroded or severely corroded　　 Moreover, the processes of these two pumps are also different and the sewage pump can generally be adjusted. Submersible pumps are generally used in some special or other places.

　　What is the cause of pump overload.Quality management,　　 The pump body (can not) bear the pressure from the outlet pipeline system. The standby pump in the warehouse should rotate (/ times a week to make the shaft bear the load and external vibration evenly. The belt CR drive is that the motor is on the (right) side of the pump from the inlet of the pump.　　Many customers need to replace the impeller after purchasing the slurry pump. What if the impeller of the slurry pump cannot be disassembled?　　 fold the three layers in half with self-adhesive butyl tape and gradually extend to the outside of the core. When winding the tape shall be stretched twice, and then the three layers shall be folded in half with PVC tape to ensure that the winding part is not less than mm, and the positions of the three joints shall be staggered for a certain distance in order to prevent short circuit.Utsunomiya,　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.　　The water slurry pump is a widely used equipment. Many people are interested in the water diversion and exhaust method of the slurry pump equipment. Now let&#;s talk about the water diversion and exhaust method of the submersible slurry pump: the submersible slurry pump needs to pump out the water to form a vacuum, and then supply water,　　Flexibility. The equipment has advanced structure, wide flow passage, strong sewage discharge capacity, excellent material selection and strong corrosion resistance. It is suitable for conveying liquids containing solid particles,UtsunomiyaSmall deep well pump, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.