Xhy- series high hardness alloy I-beam; Undertake drawings and process wear-resistant pipes（ Φ ≥mm）； Undertake the processing and production of vulnerable parts of cement machinery; Welding technology consultation and service; The wear-resistant layer of alloy wear-resistant plate of high chromium heap welding flux cored wire series is mainly high chromium, as well as manganese, molybdenum, niobium, francium and other components. The alloy carbide formed has strong stability at high temperature.→ compared with the concrete structure, the I-steel structure can increase the service area by %,UtrechtHow much is the I-beam rental per ton, reduce the self weight of the structure by % - % and reduce the structural design internal force.Utrecht,The electric welding reinforcement mesh can reduce the damage and consumption to the reinforcement processing process. According to statistics, after deducting the steel consumption increased by unit lapping, it can also save about % of the steel. After it is transported to the site according to the construction degree of the project, it can be hoisted to the working face. There is no need to set a reinforcement processing site on the site, which saves the site and increases the management level of the site. At the same time, it can also solve the problems of noise pollution caused by straightening reinforcement. Remove defective pipes within the allowable length.San Sebastian,Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members.Heating surface pipes, economizers, reheaters, pipes for petrochemical industry, etc. for high-pressure boilers (working pressure is generally above MPa and working temperature is between ℃ ~ ℃)I-beam, also known as steel beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.

Application characteristics of I-beamClassification by end shapeI-beam is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'.Analysis project,I-beam, also known as steel beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape. Judged as failing.I-beam is mainly divided into ordinary I-beam, it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are -, that is, the corresponding height is -. At the same height, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam,UtrechtHow much is Q235 I-beam per ton, also known as H-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.

Alloy tube is widely used in our daily life which provides us with great assistance. So what industries are alloy tubes applied to? Let&#;s follow the steps of all manufacturers and have a look together:Economic management,Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.There shall be no bending at the welded junction,UtrechtPrice of DN65 galvanized pipe, and there shall be no staggered joint during assembly. Electric welding positioning is generally spot welding. After inspection and straightening, the free conversion method shall be used for welding as far as possible.Defects of alloy pipe and solutions:Utrecht,→ under the same section load, the weight of hot-rolled H steel structure is reduced by % - % compared with the traditional structure.Difference and application description between H-beam and I-beamWhen we carry out different projects, we must use different raw materials which can ensure the quality of the project. In many kinds of data, alloy pipe is widely used. In many projects, we will apply it, so it is very popular in the field. When people carry out the construction of alloy pipe project, there are many things that must be paid special attention to. Let&#;s take you to know: