Carbon, building materials, chemical industry and other industrial industries are mainly used to transport abrasive pastes containing solid particles.　　 Assembly of rotor parts of submersible slurry pump Before assembly,AllahabadWQ submersible pump parameters, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.Allahabad,　　 Ensure that the electric pump operates normally The electric pump needs to be equipped with a fully active water pump control cabinet when there are no other conditions. Do not directly connect the power grid or use a knife switch to connect the power supply.　　During normal operation, the temperature of the motor is very high, some even as high as ℃. In this case it is easy to burn the motor and replace it with a new one. In fact,AllahabadQuotation slurry pump, one motor burns out at this time. Don&#;t worry about replacing it. You must find out the cause of the motor&#;s heating, orMuisne,　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged, so we need to replace them regularly during use　　Check whether it needs to be replaced.　　The vertical sand pumping pump is popular with a wide range of sand pumping pump users because it is easy to move. This equipment is made of high-tech endurance data. Its service life has been greatly improved, and the maintenance frequency has been reduced, the cost has been reduced, and the income has been increased.　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged, so we need to replace them regularly during use　　Check whether it needs to be replaced.

　　Water or air leakage in the pipeline. The nut may not be tightened during installation. If the leakage is not serious, the air or water leakage can be treated with cement or cement slurry mixed with asphalt oil. Temporary repairs can be done with some wet mud or soft soap. If water leaks at the water pump joint, tighten the nut with a wrench. as　　 observation method: people can visually observe whether the machine parts on the submersible slurry pump are loose, cracked and damaged. Through comprehensive ysis of various observation information, we can judge whether the pump has fault, fault location, fault degree and fault cause.　　In fact, but it is adjustable. During normal operation,　　 It may also be because the pump&#;s liquid supply pipe is blocked by other substances during normal use.　　Be sure to choose a pump that is more suitable for use.　　Only in this way can its service life be extended to a large extent.

　　 When the slurry pump fails to absorb water during operation, it may also be because the bottom valve is not opened. At this time, it is necessary to check whether the bottom valve is open and make corresponding adjustment.install,　　Be sure to choose a pump that is more suitable for use.　　In recent years domestic stainless steel pipeline pump products have greatly improved their technical level through introduction, absorption, renovation, digestion and innovation, especially the supporting products of some major technical equipment have reached or approached the advanced level of similar products.　　Analysis of installation problems of slurry pump For bearings lubricated with thin oil, oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.Allahabad,　　In recent years, the demand for submersible slurry pumps has increased greatly. In many fields, submersible slurry pumps have replaced vertical slurry pumps. What are the differences between the two? Let&#;s yze.　　Although the shaft seal occupies a small position in the pump, the normal operation of the pump is closely related to the shaft seal.　　First the reason for the motor body: the wrong connection will make the temperature rise rapidly when the equipment is used; In addition, there may be some phase to phase short circuits between stator windings, so when the situation is relatively minor