The fruit is also bad; When the axial flow pump is used, its water output is relatively large, but the head is not too high, so the effect of using the submersible slurry pump in many plain areas is also relatively good; The water output and head of the mixed flow pump are actually derived from one　　Let the medium containing some solid particles generate a certain flow rate, so that the equipment can drive the solid to flow when it is in use, so that the slurry can be transported. In terms of the principle of the submersible slurry pump, it is actually quite simplePecambaru,　　How to prolong the service life of the submersible sewage pump Replace the sealing ring: after long-term use in the sewage medium, the gap between the impeller and the sealing ring may increase so it should be replaced in time.　　Then it can enter into the volute pump housing. Then in the volute pump casing, the medium slows down because the flow channel is also gradually expanding.Perpignan,　　There is no need to equip auxiliary mixing or spraying equipment,PecambaruPipeline pump body, and the operation is simpler. The equipment is directly submerged for operation, without noise and vibration, and the site is cleaner.　　 Assembly of rotor parts of submersible slurry pump Before assembly, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.　　Water pump is a kind of machinery that pumps energy liquid. It is a machine that converts the mechanical energy of the prime mover into the potential energy of the pumped liquid. Driven by power machinery,PecambaruUsed pipeline pump,PecambaruRubber lining submerged slurry pump, it can pump liquid from low to high or far away to serve production.

　　With water, you can start working.　　Fire fighting awareness is deeply rooted in the hearts of the people. With the improvement of fire fighting awareness, many people pay more and more attention to fire pumps. Some places also began to pay attention to the selection of fire pumps. In many places, fire control cabinets are also installed under the full set of fire control systems. In earlier years, fire control　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakageGood reputation, the cut impeller is usually used. The cut is　　 First of all, we need to know that submersible pumps generally operate in water. In fact, most of the pumps are suitable for conveying some relatively clean media, and their impellers are generally in a closed state. However one of the media conveyed by sewage pumps may　　Analysis of installation problems of slurry pump For bearings lubricated with thin oil, oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.

　　Function of shaft seal of submersible slurry pump: the main of shaft seal is to prevent high-pressure liquid from leaking out of the pump and prevent air from entering the pump.High value,　　When the water level reaches, the frequency of the frequency converter drops, and the slurry pump operates at a low speed. The higher the water level, the lower the speed; The lower the water level, the higher the speed. At the same time, the water level signal is transmitted to the control cabinet so that the operators can timely understand the liquid level. Through this control, the circulation in the slag slurry pool is basically unchanged　　The slurry tip of this series is a horizontal slurry pump, which is divided into ah series: the overflow part is made of high chromium alloy, and AHR series: the overflow part is made of natural rubber. It is a double pump casing structure, and the lining is professionally called sheath, which is made of high chromium alloy. If AHR series　　Moreover because the length of the long shaft is generally fixed, it is often troublesome to install it. Therefore, when it is used later, the place where it operates will also be limited. If the equipment willPecambaru,　　It, generator and market formed at the beginning of construction have gradually formed a certain scale after more than ten years of rapid development. In the early stage, in order to meet the needs of market development, water pumps and generators　　In order to make the equipment perform better when it is used, but this also needs to be based on its working principle. It can not be adapted at will when it is optimized.　　Yes, such mechanical faults will cause the stator winding of the pump to be burnt out.