important parts shall be marked in advance to avoid errors during resetting. The joint surface and vulnerable parts shall be properly kept to prevent damage.　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged, so we need to replace them regularly during use　　Check whether it needs to be replaced.Badamdar　　; When the electric pump has sudden noise or large vibration; When the protection switch frequency trips.　　 important parts shall be marked in advance to avoid errors during resetting. The joint surface and vulnerable parts shall be properly kept to prevent damage.Dobele,　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.　　Water flow into the bearing damages the bearing.　　Its main features are as follows: the whole machine is a dry-type motor pump structure. The motor is protected by mechanical seal, which can effectively prevent high-pressure water and impurities from entering the motor cavity. In addition to the main impeller, it is also equipped with a mixing impeller, which can pump out the slag settled at the bottom after stirring into turbulence. impeller

　　The motor is scrapped. Moreover, because the length of the long shaft is generally fixed, and the application occasions are subject to many restrictions.　　This series of slurry pumps are self-developed slurry pump products in China, with simple structure, belonging to medium and light slurry pumps; ZGB series slurry pump, this series of slurry pump is a heavy-duty slurry pump, which can be used in series; When SP and ZJL series work, some pump bodies can　　 In addition, the noise method directly detects the noise of the equipment in the detection process, but this measurement will also be affected by the surrounding noise, so in fact, this measurement is not very accurate.device management,　　 there is also a simple method to measure the vibration frequency of the pump by vibration method. However, when using one method, there may be some errors in the measurement results. When many equipment are used there are other vibration sources that will affect the measurement results. Therefore, in fact,BadamdarWear resistant slurry pump, it is mainly　　 The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked,　　The submersible slurry pump is a slurry pump which is connected with the motor and works under the water at the same time. Compared with horizontal slurry pump and vertical slurry pump, the biggest advantage is that it is flexible, convenient and easy to apply to various working conditions. The most important technical point of submersible slurry pump is the tightness between its motor and pump body Stability and reliability of seals.

　　The of descending axial force can be used for slurry transportation in power plants,BadamdarSubmersible pump can pump sewage, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min, which is mostly used to transport flammable, explosive,BadamdarAh slurry pump, toxic, high pressure and low temperature.Supply chain quality management, and then supply water,　　It can be that there is water leakage in the pipe gasket pipe or pump body. If the current is greater than usual, we should look for problems from the wear of vulnerable parts.　　 It may be that the motor power of the water pump is too large, the working current is too large, and the heat generation is too large, resulting in the high temperature of the vacuum pump.Badamdar,　　Slurry pump Inappropriate model is selected when selecting the pump. In actual use, when the load conditions do not match the model of the slurry pump, for example, the pump lift used is too high or too low, which will lead to overload, so we are selecting the pump　　Then it can enter into the volute pump housing. Then in the volute pump casing, the medium slows down because the flow channel is also gradually expanding.　　The purpose is to avoid water leakage of the pump, but the water seal may be damaged due to faults after being used for a period of time. Let&#;s learn how to replace the water seal.