The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.Stages needing attention in the production and manufacture of alloy tubesSanto Domingo,Galvanized pipe: the hot-dip galvanized pipe base plate and molten electroplating solution are combined physically and chemically to form a dense corrosion-resistant structure of zinc iron alloy layer. The alloy layer is integrated with the pure zinc layer and the steel pipe substrate. Therefore, it has strong corrosion resistance.I-beam, also known as steel beam,The delivery length of I-beam is divided into fixed length and double length,Santo Domingo40Cr alloy pipe manufacturer, and the allowable difference is specified in the corresponding standards. The length selection range of domestic I-beam is divided into -, - and - according to different specification numbers. The length selection range of imported I-beam is generally -.Precision cold rolling of small and medium-sized bearing sleeves with alloy tubes can greatly improve material utilization, bearing performance and service life. This paper systematically introduces the development of high quality cold drawn bearing steel pipe and its application in bearing. Precision cold rolling of small and medium-sized bearing sleeves with bearing steel pipes can greatly improve material utilization, bearing performance and service life. This paper systematically introduces the service life of high quality cold drawn bearings.H-section steel belongs to high-efficiency and economic cutting profile (other cold-formed thin-wall section steel, profiled steel plate etc.). Due to the reasonable section shape, they can make the steel give more play to its performance and improve the cutting capacity. Different from ordinary I-type, the flange of H-section steel is widened, and the inner and outer surfaces are usually parallel so it is convenient to connect with other components with high-strength bolts. Its size composition is reasonable, series and models are complete, which is convenient for setting

Nitriding: also known as nitriding, it is the process of penetrating nitrogen atoms into the surface layer of steel. At present, gas nitriding is widely used in the production of alloy steel pipe.First, we can clean the outer surface of the welded pipe with solvent or emulsion. This method is very effective for cleaning the oil stain, dust and other organic matters on the surface of the welded pipe.Heating surface tubes for low and medium pressure boilers (working pressure is generally not greater than MPA and working temperature is below ℃);original,What is nitriding of alloy pipeWhether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, the special rolling method can be used to make full use of the skills of uneven deformation and pass design. For example, when the billet section is narrow and wide I-beam is required to be rolled, the wave rolling method can be used; for example, when the billet is wide and small I-beam is required to be rolled, the negative rolling method can be used Spread rolling, etc.

Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.details,→ I-beam can be processed into T-beam, and honeycomb beam can be combined to form various section forms, which greatly meets the needs of engineering design and manufacturing.Steel transfers heat excellently; Can withstand high temperature; Strong and strong materials; Probably a long time ago. In addition, there is the low cost of metal.Because all parts of I-beam are arranged at right angles, I-beam has the advantages of strong bending resistance, simple construction, cost saving and light structural weight in all directions, and has been widely used. The inner and outer sides of the flange of the I-beam are parallel or close to parallel, and the end of the flange is at a right angle, so it is named parallel flange I-beam. The web thickness of I-beam is smaller than that of ordinary I-beam with the same height of web and the flange width is larger than that of ordinary I-beam with the same height of web,Santo Domingo12cr2mo1 alloy pipe, so it is also named wide edge I-beam.Santo Domingo,Because the section size of ordinary I-beam and light I-beam is relatively large and narrow, the moment of inertia of the two main shafts on the section is quite different, the use of I-beam should be reasonably selected according to the mechanical properties, chemical properties, weldability and structural size of I-beam.I-beam,Santo Domingo12cr5moi alloy pipe, whether ordinary or light, can only be directly used for bending members or lattice members on its Web because of its large and narrow section size and large moment of inertia difference between the two main axes on the section. It is not suitable for axial compression members and flexural members perpendicular to the web plane, so its application range is very limited. I-beams are widely used in buildings and other metal structures.Welded steel pipes need to be processed through various processes before application. The heat treatment of welded steel pipes is a very important link in the processing of welded steel pipes. Hot working is a metal hot working process in which metal materials are heated, insulated and cooled in a certain medium, and their metal properties are controlled by changing the metallographic structure on the surface or inside of the material. During the heating and cooling process of structural welded steel pipe workpiece, due to the inconsistency of cooling speed and time between the surface and the core the temperature difference will be formed, which will lead to uneven volume expansion and contraction and produce stress, thermal stress.