Because the section size of ordinary I-beam and light I-beam is relatively large and narrow, the moment of inertia of the two main shafts on the section is quite different, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design, the use of I-beam should be reasonably selected according to the mechanical properties chemical properties, weldability and structural size of I-beam. Small longitudinal crackLimera, Application of galvanized pipeAiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects,LimeraAll selection of Cold Drawn Welded Pipe, reduce strength, improve plastic deformation,LimeraHow much is I-beam 160 per ton, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.Dzuunmod,It is often asked that the shape of I-beam is similar to that of H-beam. What is the difference between them? Many people can&#;t explain it in detail. Here is a detailed answer for you: many people think that I-beam is a domestic name and H-beam is a foreign name. In fact, this cognition is wrong. H-beam and I-beam are different in shape!The alloy tube can be hardened by induction heating, so it has excellent rolling fatigue characteristics and corrosion resistance. Therefore, this kind of steel has been widely used as the material of rolling mill flap ball screw in rolling mill manufacturers. In addition to the excellent properties of cronidur steel, the modified LNs steel of case hardening steel also has the surface compressive stress characteristics obtained by heat treatment, we must use appropriate methods to carry out installation in the case of installation, so as to ensure the performance index of the data. Generally, when installing alloy pipes, so as to ensure that the raw materials can be fixed very well. Therefore, when we carry out use, we must ensure the quality of flanges and elbows, so as to ensure the actual effect of alloy pipe assembly. If there are instrument panel components that must be assembled on the pipeline, they must be installed together.Speed up the construction progress: weld the mesh with reinforcement to allow the rapid construction of the project. The required laying of welded steel bars is provided, so concrete can be poured, steel cutting, stitching, etc., and the arrangement can be strengthened. ？ saving construction time? The construction progress is greatly accelerated and the construction period is shortened.X-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe, dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids, yibai%sx ray or ultrasonic testing shall be carried out. For the spiral welding of alloy pipes for the transportation of water, wastewater, gas, heating steam and other general liquids, X-ray or ultrasonic testing sampling inspection (%) shall be carried out.Design brand,Advantages of using I-beam: reduce maintenance cost reduce downtime, improve equipment operation rate reduce wear, reduce equipment capacity and increase power consumptionThe high-temperature passivation treatment of alloy pipe is to obtain the passivation treatment film by heating in the heat treatment equipment. Before passivation treatment, the surface layer of parts must be removed to remove waste. At a higher temperature, the passivation treatment film can be obtained according to the transformation temperature and time. The hue of passivation treatment film can refer to the annealing color of alloy pipe, and the main parameters of ambient temperature and time of heat treatment process can be selected. Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time, and the waist is parallel to the roll axis.

Because all parts of I-beam are arranged at right angles, I-beam has the advantages of strong bending resistance, simple construction, cost saving and light structural weight in all directions, and has been widely used. The inner and outer sides of the flange of the I-beam are parallel or close to parallel, and the end of the flange is at a right angle, so it is named parallel flange I-beam. The web thickness of I-beam is smaller than that of ordinary I-beam with the same height of web, and the flange width is larger than that of ordinary I-beam with the same height of web,I-beam is mainly used in building structure, curtain wall engineering, mechanical equipment and vehicle manufacturing.Why are galvanized pipes so good?The sodium cyanide passivation treatment of alloy pipe can be divided into four categories. Before passivation treatment, the surface of alloy pipe shall be clear of oil stains, pickled and passivated. Passivation treatment can be carried out only after the surface is cleaned, and the workpiece of alloy pipe products can be infiltrated into aqueous solution. The passivation treatment of the alloy tube in sodium cyanide transforms the surface layer into a very thin passivation treatment film, which determines that the color of the surface layer has no change before and after passivation treatment, and the reproducibility of the solution is good.Limera,The finished product has smooth surface, flatness error + / - mm / m length, wear resistance and maximum temperature of ℃I-beam is widely usedApplication characteristics of I-beam: