Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles is often corroded. In addition to common collisions, small rocks on the driving tires, there may also be a peeling paint spot, and a small rust will appear after a long time. Because most of these scars are small, they are easy to ignore. Therefore, check regularly, the engine compartment cover and its surroundings, and once found, go to a professional beauty shop for processing.Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.Chula Vista,The main structure and application of the guide rail elevator: the mechanical part of the guide rail elevator mainly includes three parts: the lifting device, the track device and the belt changing device. The main function is to provide the moving track to make the operation more smooth. The belt changing device is used to switch the track when the elevator is going to pass the door. Lifting device The internal structure of the lifting device is mainly composed of gear mechanism, bracket, worm gear, guide mechanism, boom, upper and lower shells, etc. Gear mechanism The gear mechanism mainly includes large and small gears, a winding wheel, a middle shaft, and a safety device composed of a stop buckle and a torsion spring.The hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type car modified type, car type, auxiliary self-propelled type, and the lifting height ranges from a meter to s meter.Alamar,The use of elevators is not to maintain and overhaul after the equipment fails. It is necessary to maintain the equipment according to the correct maintenance and overhaul, and start with the preparation work to prevent all possible failures and accidents. I hope that the editor can summarize the knowledge points today. Help everyone.What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress, and new and old customers are welcome to come to consult.In addition,Chula VistaBuilding guide rail lifting cargo elevator, etc. to prevent damage to bearings or gears due to excessive axial force or radial force. Be sure to tighten the mounting bolts before tightening the force bolts. Before installation, clean the anti-rust oil on the motor input shaft, the positioning boss and the connection parts of the elevator with gasoline or zinc and sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation, and to prevent unnecessary wear and tear.

The price is guaranteed, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.The concept of the hydraulic boarding bridge power system of the boarding bridge, the large oil cylinder lifts the entire equipment slant plate, when it rises to the maximum height, and the loose-leaf tongue plate is stretched out. The equipment plates are all made of high-quality patterned steel plates and profiles for effective welding ,long lasting.The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.Information recommendation,The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage,Chula VistaA cargo elevator, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.Ensure good power supply at the installation site, install a separate distribution box, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally, there will be no electric shock, but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.

It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.Where to sell API,Low cost: The cost is much lower than that of the scissor-type mobile lifting platform,Chula Vista4-ton hydraulic lifting cargo elevator, so when purchasing a lifting platform, you must consider the scope of use of the lifting platform the frequency of work, the load and other factors to choose a lifting platform that suits the work requirements .The ripper does not move up or down or the lifting force is weak: the pressure adjustment of the relief valve does not meet the requirements and adjust the pressure to the required value; see the cleaning in item above for the internal leakage of the oil cylinder; the reversing valve is locked or internal leakage; The oil tank is blocked; the oil supply pump is faulty; the one-way valve checks the wear and damage of the one-way valve core and valve seat, and whether the one-way valve spring is fatigued or deformed.Prepare the foundation according to the foundation plan, pay attention to the alignment leveling, and alignment to ensure the level of the foundation and various requirements for use.Chula Vista,The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply, and diesel engine.Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts, etc. are loose, if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course