Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members.I-beam is widely usedBanzhuo Wen,Oxygen blowing welded pipe: it is used as steel blowing pipe. Generally, small-diameter welded steel pipe is used. There are eight standards from / inch to inch. Made of , , , or q-q steel strip. In order to prevent corrosion, some are aluminized. The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard.Santiago del Torno,In order to make the steel pipe workpiece have the required mechanical physical and chemical properties, in addition to the reasonable selection of materials and forming processes, heat treatment process is often essential. Steel is the most widely used material in the mechanical industry. The microstructure of steel is complex and can be controlled by heat treatment. Therefore, the heat treatment of steel is the main content of metal heat treatment. In addition, aluminum, copper, magnesium titanium and their alloys can also change their mechanical, physical and chemical properties through heat treatment to obtain different service properties.Due to the unique performance of I-beam, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.

Frame line crackHardness of reinforcement construction of reinforced mesh on concrete bridge deck; Including key lime mixing and packaging materials, you need to pay attention to calculating the size of the building, and the calculated specifications must meet the quality standards and construction standards.→ wide flange and large lateral stiffness. Strong bending resistance.knowledge,According to the national standard of hot rolled H-section steel in China (GB / t-, H-section steel is divided into narrow flange, wide flange and steel pile, whose codes are Hz, HK and Hu respectively. Narrow flange H-section steel is suitable for beams or compression bending members, while wide flange H-section steel and H-section steel piles are suitable for axial compression members or compression bending members. Compared with H-section steel, W, IX and iy are not as good as H-section steel under the premise of equal weight.The flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small) a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.Whether I-section steel is ordinary or light, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane,Banzhuo WenReinforcement rapid turnover software, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.

Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects, reduce strength, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.Promotion,Dehydrogenation solution: the alloy pipe shall be dehydrogenated after passivation treatment to avoid alkali embrittlementThe monthly summary of the real estate industry shows that there is a significant positive correlation between the market sales and the long-term trend of the apparent consumption of galvanized pipe, but there will also be a backwardness of the market in a special stage, and after the backwardness of the market in stages,Banzhuo Wen8-inch welded pipe, more than one meter, there will be a rapid decline in the moving average of the apparent consumption of galvanized pipe, welded steel pipe and so on.Its heat sealing effect is remarkable. It can be directly buried immediately, which can not only save resources, but also reduce consumption, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection, reduce heating equipment, unique and convenient installation, and reduce the construction cycle time of the project. On the whole it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.Banzhuo Wen,Advantages of using I-beam: reduce maintenance cost, improve equipment operation rate, reduce wear, reduce equipment capacity and increase power consumptionPass designCarburizing: carburizing is the process of penetrating carbon atoms into the surface layer of steel. It also makes the low-carbon steel workpiece have the surface layer of high-carbon steel, and then after quenching and low-temperature tempering, the part of the workpiece can maintain the toughness and plasticity of low-carbon steel.