so it can only bear the force in one direction. Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time

The side length of I-beam is small and the height is large, and the waist is parallel to the roll axis.Addujair,However, compared with plastics, these pipes, like other metals remain stable and will not be affected by high temperature.The section of I-beam has good straight pressure and tensile resistance, but the section size cannot resist torsion because the wing plate is too narrow. On the contrary, H steel has its own advantages and disadvantages.Genet,In order to make the steel pipe workpiece have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming processes, heat treatment process is often essential. Steel is the most widely used material in the mechanical industry. The microstructure of steel is complex and can be controlled by heat treatment. Therefore, the heat treatment of steel is the main content of metal heat treatment. In addition, aluminum, copper, magnesium, titanium and their alloys can also change their mechanical, physical and chemical properties through heat treatment to obtain different service properties. Frame line crackXhy- series high hardness alloy I-beam; Undertake drawings and process wear-resistant pipes（ Φ ≥mm）； Undertake the processing and production of vulnerable parts of cement machinery; Welding technology consultation and service; The wear-resistant layer of alloy wear-resistant plate of high chromium heap welding flux cored wire series is mainly high chromium, as well as manganese, molybdenum,AddujairWholesale of No. 16 I-beam, niobium, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.Generally in terms of strength, toughness and mechanical properties. There are many differences. Hot dip galvanized pipe: the coil formed by welding the square pipe with steel plate or steel strip is placed in the galvanized tank on the basis of the square pipe to form a series of chemical reactions on the square pipe. The production process of hot-dip galvanized steel pipe is simple, the production efficiency is very high, and there are many varieties and specifications. The demand for RHS by equipment and capital is very small,AddujairHow much is 14 I-beam, which is suitable for the production of small galvanized steel pipe plants. However, the strength of steel is much lower than that of seamless steel pipe. It is mainly used for drying, redox method and characteristic table.The sodium cyanide passivation treatment of alloy pipe can be divided into four categories. Before passivation treatment, the surface of alloy pipe shall be clear of oil stains, pickled and passivated. Passivation treatment can be carried out only after the surface is cleaned, and the workpiece of alloy pipe products can be infiltrated into aqueous solution. The passivation treatment of the alloy tube in sodium cyanide transforms the surface layer into a very thin passivation treatment film, which determines that the color of the surface layer has no change before and after passivation treatment, and the reproducibility of the solution is good.Job description, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, a layer of zinc is deposited in the pipe.Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.→ the two surfaces of the flange are parallel to each other, making it easy to connect, process and install.

The key purpose of grinding and polishing alloy pipe is to moisten the surface, and the relevant limit accuracy or appearance change is not easy to change.Where is good, Cold extrusion. This kind of processing method is more purposeful. Before the preparation of steel processing and extrusion molding, the investment of machinery and equipment is less, so the raw material consumption is also very small, and the technology is relatively perfect. Once the tube size is increased, the cold extrusion method must have large cargo capacity and high-power machinery and equipment. Therefore, the automatic control system will be upgraded. Spiral seam submerged arc welded steel pipe for general low-pressure fluid transportation (SY / t- is a submerged arc welded steel pipe for general low-pressure fluid transportation such as water, gas, air and steam which is made of hot-rolled steel strip coil as pipe blank, often warm spiral forming and double-sided active submerged arc welding or single-sided welding.Because alloy pipe is a very unique pipe fitting, we must use appropriate methods to carry out installation in the case of installation, so as to ensure the performance index of the data. Generally, when installing alloy pipes, we will use some flanges and elbows to fix them,Addujair16Mn large diameter seamless pipe, so as to ensure that the raw materials can be fixed very well. Therefore when we carry out use, we must ensure the quality of flanges and elbows, so as to ensure the actual effect of alloy pipe assembly. If there are instrument panel components that must be assembled on the pipeline, they must be installed together.Addujair,The import and export order of I-beam is generally based on the specifications required in use after determining the corresponding carbon structure steel (or low alloy steel) steel grade. Except for the specification number, I-beam has no specific composition and performance series. Judged as failing.Key technical characteristics of alloy pipe: