After determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.Dehydrogenation solution: the alloy pipe shall be dehydrogenated after passivation treatment to avoid alkali embrittlementSan Felipe,However, compared with plastics, these pipes, like other metals, remain stable and will not be affected by high temperature.Key technical characteristics of alloy pipeRamada, H-section steel is an economic section steel with better mechanical properties than I-section steel. It is named because its section shape is the same as the English letter 'H'. The flange of hot rolled H-beam is wider than that of I-beam, with large lateral stiffness and strong bending resistance. Under the same specification, H-beam is lighter than I-beam.Alloy pipe is a spiral seam seamless steel pipe, which is made of hot-rolled strip steel coil, often processed by warm extrusion and welded by automatic double wire double side arc welding process. The alloy pipe sends the hot-rolled strip steel to the welded pipe unit, and the hot-rolled strip steel is extruded through multiple passes. The hot-rolled strip steel is rolled slowly to produce annular pipe material with open mouth gap. Adjust the reduction amount of the extrusion roll to control the welding gap at ~ mm and make both sides of the weld flush.It is widely used in various fields of national economic construction, such as buildings, bridges, power stations, oil drilling platforms, vehicles, subways, steel structure plants and large warehouses

Because all parts of I-beam are arranged at right angles I-beam has the advantages of strong bending resistance, simple construction, cost saving and light structural weight in all directions,San FelipeHow much is the price of I-beam per meter, and has been widely used. The inner and outer sides of the flange of the I-beam are parallel or close to parallel, and the end of the flange is at a right angle, so it is named parallel flange I-beam. The web thickness of I-beam is smaller than that of ordinary I-beam with the same height of web, and the flange width is larger than that of ordinary I-beam with the same height of web, so it is also named wide edge I-beam.The chemical composition of cold-rolled ribbed strip is the same as that of hot-rolled smooth round strip. It is rolled at room temperature with hot-rolled smooth disc strip, which is called cold rolling. Due to the reorganization of steel crystal structure by cold rolling process, high tensile strength (LL, ll ll, etc.) is obtained,San FelipeHow much is 219 welded pipe per ton, which has poor ductility and cannot be welded. If there are double-sided ribs and three-sided ribs, the specification allows LL to be used as stirrup. The design value of strength is limited to n / mm?.Classification introductionHow many?,What is the purpose of flat steelAdvantages of using I-beam: reduce maintenance cost, reduce downtime, improve equipment operation rate, reduce wear, reduce equipment capacity and increase power consumptionThe wear resistance,San FelipeHow much is No. 14 I-beam per meter, fracture toughness, impact toughness and bending strength under different process conditions were compared, matching test with lubricating grease and user test it is proved that ZYS- bearing damping and antirust oil has outstanding damping effect and good antirust lubrication performance.

Judged as failing.Quality management, Peak crack Quality requirementsAlloy steel pipe is a new type of seamless steel pipe connection pipeline. The selection of pipeline connection pipeline, whether it is fire water system software, water supply equipment, or pipeline, heat and national defense industrial pipeline system software of petrochemical pipeline system, alloy steel pipe stimulates important effects.San Felipe,It is a potential rolled strip steel with rectangular section for general purpose. It is very common on construction sites. Its specifications are expressed in thickness and width. At present, most of the flat steel on the market are finished steel, which can be used ready-made for components, ladders, bridges and fences. Flat steel can also be used as blank for welding rigid steel and slab for laminated thin plate.The production process can be summarized as follows: pre leveling → finishing → straightening → post leveling. Flat steel / A / B steel with width of -, thickness of -, rectangular section and slightly pure edge. Flat steel can be finished steel, or it can be used as blank for welded pipe and thin slab for laminated thin plate.→ compared with the concrete structure, reduce the self weight of the structure by % - %