The higher the specific speed of submersible slurry pump, the auxiliary impeller of the submersible slurry pump can also reduce the axial force.　　It can improve the mechanical efficiency to a certain extent. Moreover, the molecular structure of the coating itself has good compactness, which can well isolate the air, water and other media from the pump impeller during use and also reduce the corrosion and rust as much as possibleSamragd ,　　To solve this problem, we need to regularly inspect and repair the slurry pump. Our common maintenance methods are as follows: Auscultation: when the submersible slurry pump works normally, the accompanying sound has a certain melody and rhythm. As long as you are familiar with and master these normal melodies and rhythms, you can　　 Dust and oil stains on the motor reduce the heat dissipation capacity of the equipment and cause the equipment temperature to rise.Moroto,　　When the slurry pump is working the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise,Samragd Vortex pump and pipeline pump, the motor will fall into the water　　Its main features are as follows: the whole machine is a dry-type motor pump structure. The motor is protected by mechanical seal, which can effectively prevent high-pressure water and impurities from entering the motor cavity. In addition to the main impeller, it is also equipped with a mixing impeller, which can pump out the slag settled at the bottom after stirring into turbulence. impeller　　A large amount of lubricating oil is stored.

　　Under the action of auxiliary devices, it can transport the slurry, and because the sealing device itself is special, it can also ensure the internal and external balance of the submersible slurry pump during transportation, so that the pressure at both ends of the equipment can be balanced during normal use　　 Shaft seal part auxiliary impeller shaft seal: through the impeller action of a reverse centrifugal force, prevent the slurry from leaking out. When the positive pressure at the inlet of the pump is not greater than % of the pressure at the outlet of the pump,Samragd Carbon steel explosion-proof pipeline pump, the single-stage pump or the first stage pump in series can adopt the auxiliary impeller shaft seal, and the auxiliary blade shaft seal is not required　　 Assembly of rotor parts of submersible slurry pump Before assembly, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.market price,　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impeller　　According to the user&#;s requirements, the motor can add a variety of protection devices such as water inflow detection and overheating, when the equipment is used again, the solvent in the pump is often less, and the power consumption is also less, and the efficiency of the pump in use is often improved, and the fact is

　　The development of submersible slurry pump is to adapt to increasingly complex working conditions, facilitate users to use, and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, that is, in the traditional slurry pumpLatest quotation,　　It, generator and market formed at the beginning of construction have gradually formed a certain scale after more than ten years of rapid development. In the early stage,Samragd Quotation slurry pump, in order to meet the needs of market development, generators and other mechanical and electrical products were collectively moved to the phase II market for operation. With a good business environment, water pumps and generators　　 pump room height and allowable lifting height of lifting equipment　　In this way, a smooth surface can be formed on the surface.Samragd ,　　In the mud pump the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the liquid effect is on the auxiliary impeller　When using the submersible slurry pump, the equipment may be burned out. The main reason for this phenomenon is improper operation. How should we prevent the burning out?　　If there are sundries blocked, the pump will not be filled with water. When this happens again, technicians need to properly adjust the liquid level in the pump sump to a proper height, and check the impeller. In case of damage or aging, it needs to be replaced in time