According to the diameter of the pipe, the pipe with small diameter can only be welded on one side and the technician can drill into the pipe to weld on both sides. Single side welding requires the welder&#;s technology, which can be formed by welding two on one side. Through the steel ball test, it can ensure that the cross-sectional area passing capacity and weld formation meet the design requirements. Peak crackMenzel Jemil,I-beam is mainly used in building structure, curtain wall engineering,ZhanGh2747 superalloy tube, mechanical equipment and vehicle manufacturing.Whether I-section steel is ordinary or light, due to the relatively high and narrow section size, there is a large difference in the moment of inertia between the two main sleeves of the section. Therefore, it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane which makes it very limited in the scope of application.I-beam can only be used for beam, while H-beam can be used for load-bearing column of structure.

Frame line crack The reinforcement on both sides of the inverted beam extends into the beam respectively, and the anchorage length of the reinforcement is the same as that of the reinforcement, without hook.Function of I-beam: where is I-beam mainly used?Direct material,The production process can be summarized as follows: pre leveling → finishing → straightening → post leveling. Flat steel / A / B steel with width of -, thickness of -, rectangular section and slightly pure edge. Flat steel can be finished steel, or it can be used as blank for welded pipe and thin slab for laminated thin plate.The high-temperature passivation treatment of alloy pipe is to obtain the passivation treatment film by heating in the heat treatment equipment. Before passivation treatment, the surface layer of parts must be removed to remove waste. At a higher temperature, the passivation treatment film can be obtained according to the transformation temperature and time. The hue of passivation treatment film can refer to the annealing color of alloy pipe, and the main parameters of ambient temperature and time of heat treatment process can be selected.As shown in the name, I-beam is an I-shaped section steel. The inner surface of the upper and lower flanges has an inclination, generally :, which makes the outer flange thin and the inner flange thick. Therefore, the section characteristics of I-beam in the two main planes are very different, and it is difficult to give full play to the strength characteristics in application. Although the thickened I-beam has also appeared in the I-beam market, the structure of the I-beam has determined its torsional performance.

Last week, the billet in North China market showed a slight rebound trend. The billet quotation in Tangshan, the leading city rose first and then stabilized in four trading days, with a strong wait-and-see atmosphere in the market. Affected by the almost stagnation of festival procurement, Tangshan billet fell by yuan during the Dragon Boat Festival holiday. On the first day after the festival, although the phase snail is still running at a low level, due to the small billet resources in the market, the steel mills unexpectedly rose, the steel plant has always maintained a cautious wait-and-see attitude to maintain stability.Welcome calls ,Main uses: as a finished material, flat steel can be used to make hoop iron, tools and mechanical parts, and used as building frame structural parts and escalators in buildings. Flat steel is divided into two types according to its shape: plane spring flat steel and single-sided double groove spring flat steel. Hot rolled spring flat steel is mainly used to manufacture leaf springs for automobiles, tractors,ZhanHow much is a 1.5-inch galvanized pipe, railway transportation and other machinery.Hot rolled smooth round steel is structural steel, with chemical composition content of C carbon .%, Si silicon .%, Mn manganese %, s sulfur ≤ .%, yield strength of mpa and tensile strength of MPa. High temperature continuous casting and rolling or ingot heating rolling. Soft, good weldability high ductility,.The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No. and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.Zhan, Remove defective pipes within the allowable length. Special rolling method. When it is difficult to roll the required I-beam by the usual rolling method for some reason, the special rolling method can be used to make full use of the skills of uneven deformation and pass design. For example, when the billet section is narrow and wide I-beam is required to be rolled, the wave rolling method can be used; for example, when the billet is wide and small I-beam is required to be rolled, the negative rolling method can be used Spread rolling, etc.Because all parts of I-beam are arranged at right angles, I-beam has the advantages of strong bending resistance, simple construction, cost saving and light structural weight in all directions, and has been widely used. The inner and outer sides of the flange of the I-beam are parallel or close to parallel,Zhan15CrMo thick wall seamless pipe, and the end of the flange is at a right angle, so it is named parallel flange I-beam. The web thickness of I-beam is smaller than that of ordinary I-beam with the same height of web, and the flange width is larger than that of ordinary I-beam with the same height of web, so it is also named wide edge I-beam.