It may be that the motor power of the water pump is too large, the working current is too large,GorakpurBooster pipeline pump, and the heat generation is too large, resulting in the high temperature of the vacuum pump.　　Pressure. Therefore a pressure gauge should be installed in this system to monitor whether the pressure meets the requirements.Gorakpur,　　The treatment method is as follows: first, check the circuit voltage to reduce the speed of the water pump.　　 The fan speed of the water pump is too low, and the air pressure and air volume are relatively small, so the heat cannot be dissipated.Cederbur,　　 There is also a vibration method to measure the vibration frequency of the pump, and the measurement is relatively simple. However, when using one method,GorakpurFire deep well pump,GorakpurAh slurry pump, the measurement results may have some errors. When using the submersible slurry pump, there are other vibration sources that will affect the measurement results, so it is actually the main　　Causes: there is air or gas accumulation in the water inlet pipe of the pump, or the bottom valve is not closed tightly, the water supply is not satisfied, and the gate valve or flap valve is not closed tightly.　　 When starting the slurry pump, expand the pump inlet valve and close the pump outlet valve. Then start the pump. After the pump is started, slowly start the pump outlet valve. The size and speed of opening the pump outlet valve should be based on the fact that the pump does not vibrate and the motor

　　 selection of flow: single suction pump or double suction pump shall be selected according to the flow; single suction pump or multi suction pump shall be selected according to the lift.　　 There are several reasons for the severe vibration of the pump body: the phenomenon of unbalanced rotation of the electric rotor.　　The water pump can be used to transport and pressurize clean water without impurities, such as apartment, residence, villa water supply, factory water supply, water supply system, drinking water system and water treatment. In short, there are many uses.Meticulous workmanship,　　Commodity.　　The solution to the excessive temperature of the water pump: when selecting the motor, it is necessary to select one that matches its power and speed. In addition, the cooling fan should be installed on the main shaft. It is also possible to appropriately increase the number of fan blades, but pay attention to adjusting the vacuum pump　　During normal operation the temperature of the motor is very high, some even as high as ℃. In this case, one motor burns out at this time. Don&#;t worry about replacing it. You must find out the cause of the motor&#;s heating, or

　　Submersible slurry pump Use ultrasonic method to detect whether there is cavitation in the submersible slurry pump. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps often have better measurement results when in use.property right,　　 The pump body (can not) bear the pressure from the outlet pipeline system. The standby pump in the warehouse should rotate (/ times a week to make the shaft bear the load and external vibration evenly. The belt CR drive is that the motor is on the (right) side of the pump from the inlet of the pump.　　 Damage of mechanical seal the material of mechanical seal is generally Cr or L, which is relatively rigid, not flexible and vulnerable. The installation of mechanical seal is that the static ring is fixed outside, and the moving ring is fixed with the pump shaft. When the slurry pump reverses, and the impeller retreats　　 The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked,Gorakpur,　　Ordinary vertical motor can be used without waterproof, while the motor shaft and pump shaft of submersible slurry pump are coaxial, so the motor must be waterproof and sealed, and the motor and pump can be immersed in liquid at the same time; The vertical slurry pump is an early product, and the submersible slurry pump is a newly developed product according to the market demand　　 selection of flow: single suction pump or double suction pump shall be selected according to the flow; single suction pump or multi suction pump shall be selected according to the lift.　　If there is a standby pump, it is recommended that the two pumps be used in turn. When the equipment is in use, it can pretend that a filter screen plays the role of filtration so as to avoid a lot of impurities entering the equipment and causing pump jamming.