The surface of galvanized square pipe treated by sand blasting, shot blasting or pickling process is relatively clean, and the oxide scale and rust are removed, which improves the adhesion of the coating. When the installation site unconditionally adopts sand blasting and shot blasting manual and mechanical derusting can be adopted, but the derusting quality level must be reached.Spraying (throwing) derusting spraying (throwing) derusting is that the high-power motor drives the spraying (throwing) blade to rotate at high speed, so that the steel sand, minerals and other abrasives can be sprayed (thrown) on the surface of the square tube under the action of centrifugal force iron wire section, which can not only completely remove rust, oxides and dirt, but also the square tube under the violent impact and force of abrasives, It can also achieve the required uniform roughness.Sondes,When we understand the causes of defects in the drawing process of qb square tube, we should constantly improve the technology in the subsequent production process, the carbon content generally does not exceed %. In addition to iron and carbon, the main elements of steel also include silicon, manganese, sulfur, phosphorus, etc. There are various classifications of steel and square tubes, mainly including the following: square tubes are classified into ordinary steel according to quality (P & le; .%, S & le; .%)Yabrud,Fatigue strength, plasticity and hardness discussed above are indicators of the mechanical properties of metals under static load. In fact, many machine parts work under cyclic load under which fatigue will occur.The disadvantage of solid bending is that it has tensile thinning effect. The actual bending will produce tension at the bending point, and the tensile effect will shorten the longitudinal length of the bending line; The metal at the real bend will become thinner due to stretching.Functional index analysis of qb square tube - angular plasticity refers to the power of plastic deformation (permanent deformation) without destruction of qb square tube data under load.

Cold drawn or cold rolled precision square tube (gb-) is a cold drawn or cold rolled precision square tube with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision square mechanical structure or hydraulic equipment can greatly save machining hours, improve material rate and improve product quality.After, the workpiece forms an oxide film with a fixed thickness and presents various colors. Chemical oxidation method is to form various film colors in a specific solution at temperature and time; Because of the law & rdquo; More, but to maintain the color of the product, the reference electrode must be used. Electrochemical method is to form the color of chloride film with fixed thickness in specific electrolyte at temperature, voltage and time. This process is mature and widely used. Ion implantation method is to vaporize ions in vacuum and deposit them on the surface of qb square tube, such as watch case on the market. The golden color of watch strap adopts this process technology, which is suitable for mass production. The process of gas phase cracking is more complex and less used in industry. Square tube has long been widely used in mechanical industry. When the square pipe is cut automatically, the distance difference between the two ends of one side of the pipe and the guide rail shall be adjusted within mm. During semi-automatic cutting, the guide rail shall be placed on the plane of the cut pipe, and then the cutting machine shall be placed on the guide rail gently. special shaped square pipe is the general name of square pipes with other cross-section shapes except circular pipe. According to the different cross-section shape and size of steel pipe, it can be divided into special-shaped square pipe with equal wall thickness (code D), tools and mechanical parts. Compared with circular tubes, special-shaped tubes generally have large moment of inertia and section modulus, and have large bending and torsion resistance, which can greatly reduce the structural weight and save steel. Square tubes are an indispensable part of construction workQuality recommendation,B. converter steel: (a) acid converter steel; (b) Basic converter steel. Or (a) bottom blown converter steel; (b) Side blown converter steel; (c) Top blown converter steel.Square tube plays an important role in the rapid economic development. The functions of square tube are different, and its characteristics are also different. Square tube has strict standards. There are many welding processes and advantages of square tube. Let me show you the welding process and advantages of lower tube.It is good to purchase Baosteel's materials for cold drawing of square tubes, because Baosteel's materials are subject to grade flaw detection, and the density of steel is relatively good. After cold drawing and heating, it is convenient to line up. The steel is cold drawn at room temperature to produce plastic deformation so as to improve the yield strength. This process is called cold drawing strengthening. Square tube is generally used for product parts with high requirements. It has good willfulness and strength. The surface is better after cold drawing. Cold drawing principle.

QB square tube is a product appeared in recent years, which mainly has strict tolerance and roughness for the dimensions of inner hole and outer wall. Production process classification of large-diameter qb square tube large-diameter qb square tube is divided into hot-rolled seamless square tube, cold drawn seamless square tube, seamless square tube and qb square tube according to production process. Among them, qb square tube is divided into: (a) by process & mdash& mdash; Arc welded square pipe resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe (b) are divided by weld & mdash& mdash; Material classification of straight seam welded square pipe and spiral welded square pipe large diameter qb square pipe: plain carbon steel square pipe and low alloy square pipe. Ordinary carbon steel is divided into Q Q q SS, # steel, # steel,SondesIs square steel galvanized square pipe, Q, St-, etc.Service first,Square tubes are classified by forming: forged steel; Cast steel; Hot rolled steel; Cold drawn steel.Functional index analysis of square tube - commonly used are square tube Brinell angle (HB), Rockwell angle (HRC) and Vickers angle (HV). Angle is a gauge needle to weigh the soft and hard level of metal data. The angle method is rarely used to determine the internal angle in the current life. It uses the metal data surface tested under the fixed load of the indenter with a certain number and shape to determine its angle value according to the level of the object.At this time, if the welding wire of the same material is used for spot welding where the thickness is insufficient, it shall be welded to the fixed thickness, ground and sandblasted, and repair welding shall be adopted where there are cracks, even if the steel pipe with another large opening can be made up at one time.Sondes,With the improvement of production quality, the quality of square tubes is getting better and better. The quality of square tubes will affect our lives. Because the functions of square tubes are different, their characteristics and uses are different. I will introduce the characteristics and uses of square tubes in detail.High quality steel (P & le; .%, S & le; .%)Square pipe for conveying flammable and non flammable fluids, Standard No.: gbt (gbt - ). The representative material is l-l pipeline steel. It is mainly used to transport flammable and non flammable fluids. Low pressure or high pressure square pipes have high requirements. The purpose of large-diameter qb square pipe is qb square pipe, C-shaped steel and H-shaped steel. It is mainly used in the construction of simple plant, steel structure and other infrastructure. Qb square pipe is generally used as the frame and purlin of the plant. C-shaped steel Steel is an important support for the plant, and H-section steel is used as load-bearing. Especially in recent years, a large number of small and medium-sized enterprises have started to build spacious and bright plants. If traditional buildings are built, the time is slow, the work progress is affected, and the investment is large. For some small and medium-sized enterprises, if the investment in the plant is too high, the capital will be produced after operation Serious impact. The plant built with qb square tube,SondesGalvanized square tube merchant, C-section steel and H-section steel has the characteristics of time saving, money saving and fast use. Therefore, the sales of qb square tube, C-section steel and H-section steel have increased significantly in recent years and become the first choice for plant construction. Qb square tube, C-section steel and H-section steel are mainly used in the construction of simple plant, steel structure and other infrastructure The qb square tube is used as the frame and purlin of the plant. The C-shaped steel is used as the important support of the plant, and the H-shaped steel is used as the load-bearing. Especially in recent years, a large number of small and medium-sized enterprises around the country have started to build spacious and bright plants. If the traditional buildings are built, the time is slow, the work progress is affected, and the investment is large. For some small and medium-sized enterprises Said that if the investment in the plant is too high, C-section steel and H-section steel has the characteristics of time saving, money saving and fast use. Therefore, the sales of qb square pipe, C-section steel and H-section steel have increased significantly in recent years, becoming the first choice for plant construction. Large diameter qb square pipe plant is introduced Shao measures for effective wrinkle of seamless square pipe: check the wrinkle state, even when the wrinkle around the part is determined to be less than the clamping force, and the gradual increase of the roll gap force can be. When drawing the cone and hemispherical components, it should be increased to increase the inner diameter of the inner plate and the tensile stress of the wrinkle drawbead. Adopt the principle of loosening after tightening to loosen after tightening and ask Question.