Vertical slurry pump is an early product. Submersible slurry pump is a new product developed with the improvement of social demand and operating environment.　　 Impeller protection in order to ensure the operation of the submersible slurry pump, it is necessary to timely adjust the clearance between the impeller and the front guard plate. When adjusting the impeller clearance, first stop the pump, loosen the bolts pressing the bearing box, loosen the adjusting nuts, and roll the shaft by hand to press theAthens,AthensVortex pump and pipeline pump,　　Note: Motors for special environment can be customized according to the contract.　　Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.Tczew,　　Ordinary vertical motor can be used without waterproof, while the motor shaft and pump shaft of submersible slurry pump are coaxial, so the motor must be waterproof and sealed, and the motor and pump can be immersed in liquid at the same time; The vertical slurry pump is an early product, and the submersible slurry pump is a newly developed product according to the market demand　　After that, the secondary and tertiary pumps can be started successively until the final stage pump. After all the series pumps are started, the correct selection of shaft seal can ensure the safe and stable operation of slurry pump.

　　There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media, the difference between slag slurry and sewage is still large. Let&#;s take a look at the difference between the two.　　 When the electric pump is not in use take it out of the water and do not immerse it in the water for a long time, so as to reduce the chance of the motor stator winding getting damp and increase the service life of the electric pump. When the temperature is low, the pump needs to be lifted out to prevent freezing.　　Pump, sewage submersible pump and seawater submersible pump.reform,　　 It may be that the motor power of the water pump is too large, the working current is too large, and the heat generation is too large, resulting in the high temperature of the vacuum pump.　　Water or air leakage in the pipeline. The nut may not be tightened during installation. If the leakage is not serious, the air or water leakage can be treated with cement or cement slurry mixed with asphalt oil. Temporary repairs can be done with some wet mud or soft soap. If water leaks at the water pump joint, tighten the nut with a wrench. as　　The water slurry pump is a widely used equipment. Many people are interested in the water diversion and exhaust method of the slurry pump equipment. Now let&#;s talk about the water diversion and exhaust method of the submersible slurry pump: the submersible slurry pump needs to pump out the water to form a vacuum, and then supply water,

　　 determination of model: for water pump or pump with physical and chemical medium similar to water, it is necessary to go to the relevant product catalog or sample and make correction according to the performance table or performance curve of the model to see whether the normal working point falls in the priority working area of the pump.High quality brand,　　Screw it down, and then remove the bearing inner race, O-ring, shaft sleeve and retaining sleeve in turn.　　 It is not allowed to operate the electric pump at high lift for a long time and try to control it within the range of the proposed use lift, so as to prevent the electric pump from burning out the motor due to overload.　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.Athens,　　During the process, the equipment must be regularly maintained and overhauled to avoid blockage. As the name suggests, but in fact, we use it at ordinary times　　 When the slurry pump fails to absorb water during operation, it may also be because the bottom valve is not opened. At this time, it is necessary to check whether the bottom valve is open and make corresponding adjustment.　　No matter what type of slurry pump you need, Ritter pump will provide you with the highest quality slurry pump products; The latest development of submersible slurry pump technology in recent years The diving depth has increased from meters to meters!