When it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.Whether I-section steel is ordinary or light, due to the relatively high and narrow section size, there is a large difference in the moment of inertia between the two main sleeves of the section. Therefore, it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application.Neshabur, Pure zinc layer is a plastic zinc layer in hot-dip galvanizing. Its properties are basically close to pure zinc and have ductility, so it is flexible. Galvanized pipe is widely used in architecture. This product must have been seen by everyone. However, there are many types of it. When you buy it, you should also find out which one you need. The reason why it is favored by everyone in the market is inseparable from its advantages. Next, Xiaobian will lead you to see the advantages of galvanized pipe.d. All machines and equipment in a production line can connect with the software of the computer data collection system to complete the timely transmission of data information, and the performance parameters in the production process are monitored by the central control room.Rio Branco,I-beam has wide flange, thin web, many specifications and flexible use. It can save metal by % ~ % when used in various truss structures. Because the inner and outer sides of the flange are parallel and the edge end is at right angles, it is easy to assemble and combine into various components, which can save about % of the welding and riveting workload, greatly accelerate the construction speed of the project and shorten the construction period.Heating surface pipes economizers, superheaters, reheaters, pipes for petrochemical industry, etc. for high-pressure boilers (working pressure is generally above MPa and working temperature is between ℃ ~ ℃)It is a potential rolled strip steel with rectangular section for general purpose. It is very common on construction sites. Its specifications are expressed in thickness and width. At present, most of the flat steel on the market are finished steel, ladders, bridges and fences. Flat steel can also be used as blank for welding rigid steel and slab for laminated thin plate.

H-section steel belongs to high-efficiency and economic cutting profile (other cold-formed thin-wall section steel, profiled steel plate etc.). Due to the reasonable section shape, they can make the steel give more play to its performance and improve the cutting capacity. Different from ordinary I-type, the flange of H-section steel is widened, series and models are complete, which is convenient for settingSeamless pipeH-section steel is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'. There is no slope on the inner side of the two outer edges of H-section steel, which is straight. This makes the welding and splicing of H-section steel simpler than I-section steel better mechanical properties per unit weight, and can save a lot of materials and construction time.Highly recommended,Classification introductionAlloy pipe can be divided into round steel pipe and special-shaped steel according to different cross-sectional area. Because the circular area is large on the premise of the same side length, a large amount of liquid can be transported with an annular tube. In addition, when the circular cross section bears the internal or external axial working pressure,NeshaburHow much is Beijing Yijing steel bar turning software, the bearing force is more symmetrical. Therefore, most seamless steel pipes are round steel pipes. Cross rolling pass system. This pass system refers to that the two open legs of the I-beam pass are not on the same side of the waist at the same time, and the waist has an included angle with the horizontal axis.

I-beam has the dual properties of high hardness and toughness materials. Compared with other engineering wear-resistant materials in China, such as various alloy steel plates, cast wear-resistant plates cast stones, rubber, polyurethane, etc., it has irreplaceable comprehensive excellent properties.Pursuit of excellence, Cross rolling pass system. This pass system refers to that the two open legs of the I-beam pass are not on the same side of the waist at the same time, and the waist has an included angle with the horizontal axis. Pickling stainless steel pipe. When removing grease, rust prevention, spot welding, oxide layer, free iron and other dirt, the surface shall be treated with silver to evenly slow down the pickling surface, prevent metal corrosion and hydrogen embrittlement and inhibit fog production.All the cracks occur at -mm away from the edge below the alloy pipe, and the macroeconomic orientation is vertical to the cold rolling orientation,Neshabur16Mn large diameter longitudinal welded pipe, showing a 'high mountain' shape.Neshabur, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.The high-temperature passivation treatment of alloy pipe is to obtain the passivation treatment film by heating in the heat treatment equipment. Before passivation treatment,NeshaburT-welded pipe manufacturer, the surface layer of parts must be removed to remove waste. At a higher temperature, the passivation treatment film can be obtained according to the transformation temperature and time. The hue of passivation treatment film can refer to the annealing color of alloy pipe, and the main parameters of ambient temperature and time of heat treatment process can be selected.Application characteristics of I-beam: