Improper use of oil: Inadequate maintenance of high-altitude work platform equipment such as mobile elevators can also lead to small fitting gaps of components, making it difficult for oil to form a uniform oil film on the friction surface. Additionally, due to assembly and other reasons, it is difficult to ensure the uniformity of fitting gaps, thereby reducing efficiency and causing early abnormal wear of equipment components; In severe cases, it may cause scratches or bite on the friction surface of precision fitting, leading to the occurrence of abnormal equipment noise.The lifting platform has been inspected and debugged before leaving the factory, and all technical indicators meet the design requirements. When in use, only the power supply needs to be connected, and the hydraulic and electrical systems basically do not need to be adjusted.Winnie snowFor the introduction of daily maintenance of lifting cargo elevators, there should be no dirt present. If there is any dirt the brakes of each organization should usually be inspected and adjusted to ensure sensitivity and reliability. On the surface, it must be washed off with gasoline or thinner.Drain all the hydraulic oil in the oil tank, open the oil tank, take out the oil suction filter, clean it, and return it to the oil tank. Install it in its original position. Fill the fuel tank with new oil.Al Jizah,Regular inspection and maintenance, eliminating hidden dangers, and troubleshooting are beneficial for improving work efficiency, extending equipment service life, and ensuring the safety performance of elevators.What are the advantages of installing a guide rail type elevator for goods? The advantages of civil engineering are easy to install: there is no need for a machine room above the shaft, and the top layer can be installed at a height of more than meters. The computer room can be located within a radius of meters of the shaft, occupying an area of only - square meters. The hydraulic elevator is not equipped with a counterweight device to improve the utilization rate of the shaft area. The load and load cylinder of the hydraulic elevator directly act on the foundation pit,Winnie snowSmall hydraulic lifting and leveling, and the strength requirement for the shaft is low. A brick structure or brick concrete structure shaft is sufficient.The second is that the steel will have obvious thermal expansion effect at low temperature. Although this property of steel will be taken into account when designing and manufacturing hydraulic elevators, the steel will have some unstable performance, such as hardness increase, toughness decline, etc. At this time, and uneven damage to the inner sealing ring or obstacles inside can easily cause uneven stress, resulting in uneven lifting height of the oil cylinder. It is recommended to carefully check whether the oil cylinder is normal.Aging and deterioration of hydraulic oil; The solution is to replace the hydraulic oil.Replace with new oil and do not intermittently use old oil, otherwise the moving parts in the system will accelerate wear.Design brandWhat should I pay attention to when starting a new mobile elevator? High priced and various specifications of scissor lift manufacturers welcome scrap merchants, industrial companies, enterprises, and power departments to visit and negotiate with the company!There are three movable plates on both sides of the adjustment plate,Winnie snowImported hydraulic lifting platform, which can effectively avoid accidentally injuring the toes of operators when the adjustment plate is lowered, ensuring the safety of equipment use.When working in a hot environment, pay attention to heat dissipation.

There are problems with the hydraulic torque converter and compensation system of mobile elevators, such as weak torque converter, power shift failure, high oil temperature, inadequate pressure adjustment, insufficient back pressure. Check the quality of torque converter oil (whether hydraulic transmission oil is misused), dosage, torque converter pressure regulating valve, back pressure valve and their set pressure value. Power shift failure. Quick return valve, pressure reducing valve, power transmission valve The directional valve is stuck or leaking internally. Oil pollution is severe. Check the cause of the valve sticking and eliminate it accordingly. Filter or replace the hydraulic oil. If the oil temperature rises too much, check if there is any problem with the cooler. Check the quality of the hydraulic oil. The brand hydraulic boarding bridge, also known as the hydraulic loading and unloading platform, can achieve rapid loading and unloading of goods. The structure design is simple, the use is flexible and convenient, and the work efficiency is high. It is widely used and widely popularized in the market.install,Working at heights is a common practice nowadays, which are more convenient to help people complete high-altitude operations. However, people should also pay attention when using hydraulic lifting platforms, otherwise they can easily malfunction, which may lead to serious consequences. So what are the common faults of hydraulic lifting platforms?The above introduction to common faults of hydraulic boarding bridges can be said to be very detailed. I hope everyone can respond well to various problems after reading it.Any product always has a break-in period when it is first used, so what precautions should we pay attention to during the break-in period when using a hydraulic lifting platform? Today, the editor will share this topic with everyone.Winnie snow,The equipment operation is very simple just press the operation button, and the height adjustment board of the equipment will automatically rise; Release the button, adjust the weight of the plate to fall, and the tongue plate can be used by placing it on the truck.When conducting high-altitude operations on dangerous edges such as roofs,Winnie snowMobile hydraulic lifting platform, suspension bridges, slopes, or cliffs, guardrails or safety nets should be installed on the side facing the air, or safety belts or ropes should be used.Avoid, especially during storage. Store in a cool and dry place, and avoid rainy and snowy weather during work.