Welding is a synthetic gradient material, which can be used as solder to weld special-shaped materials in order to overcome the mismatch of chemical, mechanical and physical properties between base metals.Square tubes for petroleum cracking (gb-) are furnace tubes, heat exchangers and pipeline square tubes suitable for petroleum refineries.Alkmar,High temperature diffusion heat treatment of ingot can improve the composition heterogeneity of ingot and improve the transverse performance of square tube.When the vehicle is replaced with seamless square tube blank, so as to ensure the quality of parts and avoid wrinkles.Clarevo,The square tube is divided into a. boiling steel according to the degree of deoxidation and pouring; b. Semi killed steel; c. Killed steel; d. Special killed steel. The deformation of qb square tube is mainly caused by the shrinkage force of the weld greater than the strength of the base metal.Square tube heating process square tube calculates the chip thickness of workpiece. After each regrinding, the service life of the saw blade. Regrinding times of the saw blade. When the saw blade is replaced, the main drive AC motor spindle rotates stepless speed change AC motor feed capacity stepless speed change feed fast return to a constant value center system brush device hydraulic saw cutting system system system represents the quality RA flatness, large burr height cutting Chip length tolerance dimension: width and length . ~ .mm ~ m ~ ~ min kW ~ rpm ( kw ~ mmmin mmmin .kw .kw & times; kW S & mu; m . mm & plusmn; mm about mm about mm about mm high. The total weight of each billet square tube is seconds (including, pipe blank cutting, saw blade return, opening device, pipe blank discharge, but excluding pipe blank transportation time). The large production capacity of the three saws is T / A. the pipe blank saw has a special reversing device (hydraulic servo device) to reduce vibration and improve the service life of the saw (only during feeding). The sawing machine has two devices distributed at the inlet and outlet (the input area is supported by roller table to ensure the bending of billet) The inlet end after sawing. Open it to ensure that the saw blade does not contact the blank when it returns. & mdash; feed saw gear & mdash; saw gear vibration reduction, which is composed of a fixed gear vibration reduction, as a movable vibration reduction to avoid the axial of the saw blade. & mdash; brush and sweep device & mdash; a driving brush and sweep device is installed at the bottom of the saw blade to clean the iron filings on the teeth and will not affect the service life of the saw blade. &Mdash; saw blade. In order to improve the service life of the saw blade, a small amount of high load agent container is atomized by air and poured on the saw blade without residue. & mdash; saw blade cooling device. A special nozzle is used to spray cold air at - oC on the saw blade. The cut-off blank is transferred to the buffer chain in front of the loader after passing through the outlet roller table and weighing device (Note: # before sawing, there is a feeding bench for single size billets that need to be cut, and after weighing, and the weighed unqualified billets are transported from the roller table to the removal bench for removal.Square pipe is the name of square pipe, that is, steel pipe with equal side length. It is made of rolled strip steel after process treatment.

Zinc layer thickness: there is a great difference between cold galvanized square pipe and hot galvanized square pipe in galvanizing process; Cold galvanized square pipes are prone to & ldquo; Electric burning & rdquo; The color of this part is gray and the zinc layer is thick. It is easy to form a current dead angle at the corner, resulting in an under current area. The zinc layer at this part is thin, and there is no zinc layer attached to the cold galvanized square pipe. The cold galvanized square pipe has no zinc lump and caking as a whole, but the overall zinc layer is thin, and the thickness of the outer wall zinc layer is μ m-μ m. The and outer walls of the hot-dip galvanized square tube are attached with zinc layer, and there will be water marks and a few zinc tumors, but the overall zinc layer is thick, and the thickness of the zinc layer on the inner and outer walls of the square tube is -mu; M above. The nature of QB square tube!Application: it is widely used in machinery, construction, metallurgy, agricultural vehicles agricultural greenhouses, automobiles, railways, highway guardrails, container frames, square tubes raw materials, i.e. strip coils, welding wires and fluxes. It must undergo strict physical and chemical inspection before being put into operation.The floating mandrel mill is in its heydayEconomic management,Hundreds of degrees Celsius, which can save energy.Stage ( & mdash; )We all know very well. Therefore, the quality of square tubes will directly affect the development of the construction industry. What if we can make the service life of square tubes longer? Here, we also need to ask the personnel of the square tube manufacturer for instructions,AlkmarWhere do galvanized square tubes sell, and use ingenious methods to prolong the service life of the square tube, so that the square tube can bring us greater help in life.

Square tubes for petroleum cracking (gb-) are furnace tubes, heat exchangers and pipeline square tubes suitable for petroleum refineries.Click to view,Hundreds of degrees Celsius, Fangguan hasThe other is designed with deformation angle, which can be regarded as DEG from round tube to square tube; To & deg; The bending deformation of angle, so the deformation angle & theta; It can accurately reflect the deformation degree of corners and edges. In the design process, considering the influence of dimensional accuracy and metal work hardening, the distribution of deformation angle is usually larger at the beginning and middle passes, and then gradually decreases. In the pass formed directly by arc intersection, the fillet part of the pipe blank cannot be filled with the pass, so the pass perimeter is different from that of the pipe blank. In order to ensure the dimensional accuracy, the fillet part of the pass needs to be corrected and calculated. Therefore, this method has higher design accuracy than other methods. However, due to the large amount of iterative calculation this method is more suitable for pass design by computer. If you use a frame that deforms both horizontally and vertically, you can directly use the deformation angle & theta; Pass design.Alkmar, cold drawn tubes, tubes, etc. Hot rolled seamless tubes are produced on the automatic precision tube precision tube rolling mill. The solid tube blank is cut into the required length by removing surface defects, centering on the end face of the perforated end of the tube blank and then sent to the heating furnace for heating. It is perforated on the piercing machine. At the same time, it rotates and advances continuously under the action of roll and plug, A cavity is gradually formed inside the pipe blank, which is called the rough pipe, and then sent to the automatic pipe mill for continuous rolling. After the wall thickness is adjusted by the whole machine, and the diameter is determined by the sizing machine to meet the specification requirements. The continuous pipe mill is more advanced in producing hot-rolled seamless steel pipe. If you want to obtain seamless pipe with smaller size and better quality, Cold rolling and cold drawing must be adopted, or the combination of cold rolling and cold drawing is usually carried out on the roll mill. The seamless pipe is rolled in the annular pass composed of variable section circular hole groove and fixed conical plug. Cold drawing is usually carried out on the single chain or double chain cold drawing machine, that is, the heated pipe blank is placed in a closed cylinder,AlkmarDN32 galvanized pipe outer diameter,AlkmarQuotation for galvanized rectangular pipe, and the perforated rod and rod move This method can produce steel pipe with small diameter. In the building materials industry, the development of various pipes is different. Because of their different characteristics, in the building materials industry, the development of various pipes is different. Because of their different characteristics, there is a certain distance between pipes. Square pipe is one of many pipes in the building materials industry. It is formed after strip steel treatment. The various characteristics of steel pipe need to be understood by everyone. However, due to the of steel pipe and other raw materials, the storage of steel pipe needs specific conditions.Empty bending empty bending is the bending moment formed in one direction between the outer roll and the outer wall of the tube blank to bend the strip. Empty bending will compress the bending line, the compression effect will lengthen the bending line longitudinally, and the metal at the bending will accumulate and thicken, which is the compression thickening effect of empty bending.Generally, chemical and electrolytic methods are used