Advantages: it is warm for many days and cool in summer. Of course, the lines are comfortable on the feet and resist germs.Since the wear-resistant layer on the surface of the strengthened ground has good wear resistance, compression resistance, impact resistance, fire and flame retardancy, chemical pollution resistance and other properties, in daily use, it only needs to be cleaned with a twisted dry rag, mop or vacuum cleaner. If the ground is greasy and dirty, it can be wiped with a rag and detergent. Do not scrape or scratch the floor surface with sharp tools.Standard requirements,Third, it is flame retardant, but it cant be burned.durabilityAs mentioned above, calcium powder has good thermal conductivity, so paving the floor at home is the best choice. Even if it gets hot, it will not release harmful gases.SPC floor is a new type of floor, also known as stone plastic floor. Its base material is a composite plate made of stone powder and thermoplastic polymer, which is stirred evenly and extruded at high temperature. At the same time, it has the characteristics of wood and plastic to ensure the strength and toughness of the floor.
Domestic cheap decorative paper is usually used. The pattern of this decorative paper is fuzzy. The biggest defect is that it is generally not UV resistant and will fade after sunlight.This is why some consumers reflect the discoloration of the places near the balcony and windows three or four months after the floor is installed. The base material is poor, medium and low density board or particleboard is used, the quality index is unstable, and the formaldehyde seriously exceeds the standard.Administration,The combination of hardness and softness.The wood floor in the living room should be made of boards without knots, cracks and mildew. Generally, Fraxinus mandshurica, camphor and teak are better, because their lines are beautiful and clear, and their texture is moderate.The laying method of wooden floor is not very difficult, but it is required to have a certain carpentry foundation.Firstly, and the floor shall be cleaned before laying.When laying, draw the center point and vertical and horizontal vertical lines of the room, which is composed of evenly distributed aluminum oxide, which can achieve high hardness. Scraping with sharp hard objects such as keys can only leave very shallow traces.The pollution resistance, corrosion resistance, compression resistance and impact resistance of laminate flooring are better than other kinds of wood flooring.Shtip,What is the difference between solid wood flooring and solid wood composite flooring?The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat clean and dry, it can be glued and paved.Gluing is the last process before paving, and the tool shall be a toothed rubber scraper.During gluing glue shall be applied on the ground according to the size of the floor paint cloth,ShtipTop ten brands of laminate flooring, and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand, it can be paved. When pasting, pay attention to aligning the sidelines, and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting, and the overlapping width is about cm.Align the long steel ruler with the center of the overlap, cut with a cutter along the ruler, dont forget to take out the lower one), apply an appropriate amount of glue to the joint with a paint brush, and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, and then compact it.Finally, use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed, they can be wiped with alcohol.In this way, the whole process will be completed.Due to the improvement of the living standards of Chinese residents, the grade of interior decoration is also rising, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance, high profile, long service life and good effect.As for the ground,ShtipColor difference of laminate floor, the service life of paint, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth. Beautiful and diverse colors, seamless splicing construction convenient and fast installation.
ShtipLaying method of floor leather The quality is not bad, and the goods are delivered in time. I recommend you to buy it next time.
It's rare to buy ShtipLaying method of floor leather, I saw such a good store. The price is very favorable, the service is also very good, and the things are good. Give me a good encouragement this ti
Yes, I hope to cooperate next time. Thank you boss~~ Fast delivery, ShtipLaying method of floor leather basically satisfied.
Old acquaintances, things are as good as always, genuine ShtipLaying method of floor leather, outstanding cost performance