Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course,BazhouHigh performance elevator,The hydraulic torque converter and compensation system are faulty, such as hydraulic torque converter failure, high oil temperature, etc. The hydraulic torque converter is weak, the hydraulic oil volume is insufficient, the pressure is not properly adjusted,BazhouThree ton lifting cargo elevator, and the back pressure is insufficient. Check Torque converter oil quality (whether hydraulic transmission oil is misused) dosage, check torque converter pressure regulating valve, pressure reducing valve, power transmission valve The reversing valve is stuck and internal leakage. The oil pollution is serious. Check the cause of the valve stuck and eliminate it accordingly. Filter or replace the hydraulic oil. If the oil temperature rises too much, check whether there is any problem with the cooler, check the quality of the hydraulic oil and the brand hydraulic The boarding bridge is also called a hydraulic loading and unloading platform, which can realize fast loading and unloading of goods. It has a simple structure design, flexible and convenient use, and high work efficiency. It is widely used and popularized in the market.This kind of fixed lifting equipment can also be used in the warehouse. For example, a certain floor in the warehouse needs to be lifted to send goods or personnel into the designated warehouse.Nangang,Hydraulic pump station: special pump station for domestic lifting platform, protection device outside the pump station imported from Italy: organ m type, mesh type, iron plate seal type.Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.Knowledge popularization of scissor-type fixed lifting platform Superior performance: equipped with safety devices to prevent overloading of the lifting platform; equipped with protection valves to prevent hydraulic oil pipes from breaking; equipped with emergency descending devices for sudden power failures; Lock safety device.

As for the guide rail elevator installed outdoors, it is often exposed to rain and sunlight, so special attention should be paid to regular maintenance and inspection to avoid accidents.The elevator incidents that occurred in China in recent years in mobile elevator manufacturers are caused by three factors,BazhouSimple lifting cargo elevator, namely, human error, which is purely caused by the lack of equipment-related operators. The second type is simple lifts such as hoists that have been eliminated in China and are not allowed to be used. It is aging equipment, more prone to accidents. The third is that the quality of production is not good enough, leading to serious social security accidents.Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found, it must be eliminated in time.build,Fixed lift is a kind of transportation equipment that directly lifts and unloads goods from the ground. It is mostly used in places such as goods transportation between height differences in production lines, materials on and off the assembly line, parts lifting during large-scale equipment assembly, and fixed three-dimensional parking. So what is the new price of the fixed lift?Secondly, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box, gearbox, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found, replace them in time. If there is any looseness, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, whether the motor is overheated, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, each box, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.

Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform, which is mainly used in industrial plants, restaurants, restaurants, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?Professional is king,The price is guaranteed, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.: Chemical derusting mainly uses acid to react chemically with the metal parts of the screw jack to remove the rust products on the rusty surface of the push rod. This kind of derusting is mainly used for large-scale mechanical screw jacks. During the process, electronic instruments and other precision components are protected from acid corrosion.Are the water cooling and air cooling of the hydraulic station the same?Bazhou,What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface and if there is dirt, it must be washed off with gasoline or thinner.The load of this series of products is divided into . to . tons, and can also be customized according to user requirements, with a load of up to tons.Hydraulic pump station: special pump station for domestic lifting platform, protection device outside the pump station imported from Italy: organ m type, mesh type, iron plate seal type.