The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked,　　When the slurry pump is working, the pump needs to be placed on land the suction pipe in water, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the waterAssad ā b ā d,　　 transmission device type (gearbox transmission, flat belt transmission, V-belt transmission)　　When the water level reaches, the frequency of the frequency converter drops, the lower the speed; The lower the water level, the higher the speed. At the same time, the water level signal is transmitted to the control cabinet so that the operators can timely understand the liquid level. Through this control, the circulation in the slag slurry pool is basically unchangedFiliasi,　　Through the introduction, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close, but in fact, it also needs to be used in a correct way when it is used at ordinary times. Only in this way can　　 When adding lubricating oil to the pump at ordinary times, the metering must be controlled, and the excess lubricating oil in the pump must be discharged and replaced regularly.　　 Next, it is necessary to check the water seal. If the water seal is bakelite and the wear is not too serious, you can place abrasive cloth on the glass or dry wood,Assad ā b ā dPipeline pump body, and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However, if the thrust rubber water seal is used, when

　　; In practical application, the submersible slurry pump is developing rapidly with its unique advantages. The vertical slurry pump needs to be fixed and installed in use, which is convenient and flexible.　　 Motor disassembly: remove the base, thrust bearing, thrust disc connecting seat of lower guide bearing seat, water deflector, take out the rotor, and remove the upper bearing seat,Assad ā b ā dUsed pipeline pump, stator, etc.　　 Next, the water seal, lock ring and other parts need to be installed.Inspection requirements,　　Reasonable.　　Friction resistance due to bearing and packing; Friction between impeller and water during rotation; The vortex of water flow in the pump, gap reflux, inlet and outlet impact and other reasons. A part of the power must be consumed, so it is impossible for the water pump to completely change the power input by the power machine into effective power, in which the constant active power　　Promote the continuous expansion of the sales network group.

　　Sex is different. Although the submersible slurry pump is widely used, some people outside the industry misunderstand this. In fact, the impurity pump, dredging pump, desilting pump etc. are all in the application scope of the slurry pumpLatest quotation,　　Water pump is a kind of machinery that pumps energy liquid. It is a machine that converts the mechanical energy of the prime mover into the potential energy of the pumped liquid. Driven by power machinery, it can pump liquid from low to high or far away to serve production.　　IP high power motor. The submersible pump is YQS submersible motor (water filling type).　　At the same time,Assad ā b ā dPipeline pump, the supporting pipelines in the pump room shall be provided with vibration isolation elasticity.Assad ā b ā d,　　 The submersible slurry pump needs to be inspected after reassembly. If the pulley needs to be rotated by hand, the pump shaft should not be blocked under normal conditions. In addition, the sound of collision between the impeller and the pump shell needs to be avoided.　　Extend service life. In fact the submersible slurry pump is widely used in many lives, and there is a very important component water seal in the pump, which can separate the pump body from the motor, so it mainly plays a role in use　　As an emerging product, the submersible slurry pump has many advantages, especially filling the gap in the application conditions of the traditional horizontal and vertical slurry pumps. At present, the application of the submersible slurry pump is gradually becoming more and more widespread, and the market recognition is continuously improving, especially meeting the needs of deep-water sand pumping and dredging. At present, the depth can reach meters.