Cutting blades can be selected to cut some large block solid substances into pieces during use, so that blockage can be avoided during reuse.　　Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover, and an exhaust fan is added inside the cover to ensure the ventilation of the equipment. At the same time, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pumpHello,　　Types of centrifugal pumps, etc.　　The pump should be divided into two aspects: electricity and machinery. As for machinery,　　 The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked　　The seal cannot bear the water pressure at this depth. Once the water leaks, the motor will not work normally, resulting in damage to the submersible slurry pump. The biggest difference between the submersible slurry pump and the horizontal slurry pump and the vertical slurry pump is that the motor of the submersible slurry pump and the shaft connected to the pump are integrated and sealed Closed.　　 selection of flow: single suction pump or double suction pump shall be selected according to the flow; single suction pump or multi suction pump shall be selected according to the lift.

　　Through the introduction, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close, but in fact, it also needs to be used in a correct way when it is used at ordinary times. Only in this way can　　 requirements for suction filter pipe　　With the continuous development of slurry pump technology, submersible slurry pump has also responded to the market demand. At the same time, this type of pump is especially suitable for the depth where the vertical slurry pump cannot operate. Pay attention when using the equipment. The submersible slurry pump can operate if its depth is less than m, but it exceedsInformation recommendation,HelloBaigang deep well pump,　　 The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.　　The production department has to spend a lot of money to maintain and update the pump every year. The pumps made of cast iron bronze, rubber lining stainless steel, titanium alloy and other materials used in China&#;s mining, chemical and water conservancy projects on the Yellow River are prone to wear, short service life and many faults　　Yes, such mechanical faults will cause the stator winding of the pump to be burnt out.

　　Although the shaft seal occupies a small position in the pump, the normal operation of the pump is closely related to the shaft seal.Test conclusion,　　Pressure. Therefore, the reaction force of the impeller may directly top the pump shaft. If the rigidity of the pump shaft is insufficient, it will directly lead to the bending of the pump shaft,HelloScrew deep well pump, resulting in the damage of other accessories in the pump.　　It can improve the mechanical efficiency to a certain extent. Moreover, the molecular structure of the coating itself has good compactness, water and other media from the pump impeller during use, and also reduce the corrosion and rust as much as possibleHello,　　Analysis of installation problems of slurry pump For bearings lubricated with thin oil, oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.　　 Next, the water seal, lock ring and other parts need to be installed.　　When the pump is not in use, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in addition