The shape of I-beam is similar to that of H-beam. What is the difference between them?After the passivation treatment of alloy pipe, it is clearly proposed that water cleaning shall be carried out immediately after the aqueous solution, ~ times of water cleaning, and then chromic acid closed solution shall be carried out. Chromic acid solution must be carried out h after the subsequent water cleaning of metallographic structure and austenitic alloy pipe. Chromic acid aqueous solution (mass ratio) is % ~ %, the solution temperature is ~ ℃, and the solution time is min. Then dry.Holkin,First, on which the prefabricated micro bending plate shall be installed. The second is to erect prefabricated sidewalk beams in the cantilever part of the cantilever beam. The sidewalk beams of bridge openings on both sides are longer than the main beam, one end is supported on the cantilever beam of side pier, which can not only save resources,HolkinAlloy tube precision tube,Holkin10 I-beam price, but also reduce consumption not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection, reduce heating equipment, unique and convenient installation, and reduce the construction cycle time of the project. On the whole, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.Asse,At the same height, light I-beam has narrower legs, and No. - is medium I-beam. Imported I-beam shall be marked with actual specifications, dimensions and relevant standards.In order to make the welded pipe have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming process, heat treatment process is often necessary. In addition, the mechanical, physical and chemical properties of aluminum, copper, magnesium, titanium and their alloys can be changed by heat treatment to obtain different service properties.In order to make the welded pipe have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming process, heat treatment process is often necessary. In addition, the mechanical, physical and chemical properties of aluminum, copper, magnesium, titanium and their alloys can be changed by heat treatment to obtain different service properties.

Alloy tube is widely used in our daily life, which provides us with great assistance. So what industries are alloy tubes applied to? Let&#;s follow the steps of all manufacturers and have a look together:Special shaped pipe: square pipe, rectangular pipe cap pipe, mainly used as agricultural machinery components steel pipe for hollow rubber steel doors and windows welded by general carbon structure steel and Mn steel strip, steel windows and doors, etc.I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are -, that is, the corresponding height is -. At the same height, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam, also known as H-beam is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.Management Department,At the same height, light I-beam has narrower legs, thinner waist and lighter weight than ordinary I-beam. No. - is large I-beam, and No. - is medium I-beam. Imported I-beam shall be marked with actual specifications, dimensions and relevant standards. The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard.When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, chemical properties, weldability and structural size.

Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.How much does it cost?,H-section steel After the above process, the next step is the polishing process of stainless steel pipe. There are network standards for internal and external wall finishing of pipelines, and the internal and external surface finishing of pipelines meets the mirror standard (i.e. sanitary standard).Function of I-beam: where is I-beam mainly used?Holkin, due to the relatively high and narrow section size, there is a large difference in the moment of inertia between the two main sleeves of the section. Therefore, it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.In order to make the welded pipe have the required mechanical,HolkinSC embedded threading welded pipe, physical and chemical properties, in addition to the reasonable selection of materials and forming process, heat treatment process is often necessary. In addition, the mechanical, physical and chemical properties of aluminum, copper, magnesium, titanium and their alloys can be changed by heat treatment to obtain different service properties.