Application scope of alloy pipeGenerally, there are many passivation methods for alloy tubes, the common ones are high temperature passivation or sodium cyanide passivation.Khomeini shaher,The seamless pipe produced by the seamless pipe manufacturer is a long seamless pipe without any joints around and with hollow section. The thicker the wall of this product produced by the manufacturer, the higher the use value and economic value of this product. If its wall thickness is thinner, its processing composition will increase significantly Secondly, the product technology produced by this seamless pipe manufacturer often determines its limitations.In order to make the welded pipe have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming process, heat treatment process is often necessary. In addition, the mechanical physical and chemical properties of aluminum, copper, magnesium, titanium and their alloys can be changed by heat treatment to obtain different service properties.Najeru,X-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe, dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids, yibai%sx ray or ultrasonic testing shall be carried out. For the spiral welding of alloy pipes for the transportation of water, wastewater, gas, heating steam and other general liquids, X-ray or ultrasonic testing sampling inspection (%) shall be carried out.Alloy tube is widely used in our daily life, which provides us with great assistance. So what industries are alloy tubes applied to? Let&#;s follow the steps of all manufacturers and have a look together:Plan scheme : for high carbon steel with carbon content of more than .% and high chromium alloy pipe with chromium content of no less than %, the interval is min.

Hot hole breaking cold rolling method. This method is dominated by expansion and expands vertical sliding and skew rolling. The former one is mainly cold rolling by relatively limited mandrel mill, cold rolling by few station mandrel mill, cold rolling by three high limited mandrel mill and cold rolling by fluctuating mandrel mill. In this way, the advantages of high efficiency, low metal material consumption, excellent product quality and excellent automatic control system are more and more widely used. The competitive advantage of the latter one is low cost and short whole process. It is suitable for the processing and manufacturing of CrMoG alloy pipes with large quantities, multi specifications and high precision. Therefore, it is widely usedThe use of hot dip galvanizing has expanded with the development of industry and agriculture. Therefore,Khomeini shaher159 welded pipe more than 1m, hot-dip galvanized products have been widely used in industry (such as chemical equipment, petroleum processing, power transportation metal structure, agriculture (such as sprinkler irrigation, heating room), construction (such as water and gas transportation, wire casing, scaffold, house, etc.), bridges, transportation, etc. because hot-dip galvanized productsThe crack mainly occurs at -mm from the edge of the alloy pipe. The shape is several parallel vertical cracks of different sizes. The regularity is that the thicker the specification and model of the alloy pipe is The wider the width, the more serious the disadvantages.For more, please check,The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.H-section steel belongs to high-efficiency and economic cutting profile (other cold-formed thin-wall section steel, profiled steel plate, etc.). Due to the reasonable section shape, they can make the steel give more play to its performance and improve the cutting capacity. Different from ordinary I-type, the flange of H-section steel is widened, and the inner and outer surfaces are usually parallel, so it is convenient to connect with other components with high-strength bolts. Its size composition is reasonable, series and models are complete which is convenient for settingI-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are -, that is, the corresponding height is -. At the same height, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.

b. The professional two-sided arc welding processing technology can complete the electric welding at a good position, which is not easy to have the disadvantages of staggered joint, welding deviation and incomplete penetration, and it is very easy to manipulate the welding quality.retailer,The pickling agent in the pickling process contains many acidic substances, including hydrochloric acid, sodium cyanide, etc., which has strong corrosion and reduction, and the temperature of etching substances is relatively high. Therefore, the corrosion resistance of alloy pipes is specified higher.In order to improve the corrosion resistance of steel pipe, the general steel pipe (black pipe) is galvanized. The galvanized pipe is divided into hot-dip galvanizing and electric steel zinc. The hot-dip galvanizing layer is thick and the cost of electric galvanizing is low, so there is galvanized pipe. Miscellaneous scabKhomeini shaher,The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.→ wide flange and large lateral stiffness. Strong bending resistance.Last week, the billet in North China market showed a slight rebound trend. The billet quotation in Tangshan, the leading city, rose first and then stabilized in four trading days, with a strong wait-and-see atmosphere in the market. Affected by the almost stagnation of festival procurement, Tangshan billet fell by yuan during the Dragon Boat Festival holiday. On the first day after the festival, although the phase snail is still running at a low level, the steel mills unexpectedly rose, and the billet market rebounded. However, due to the continuous increase of capital pressure and the downturn in the transaction of downstream finished materials, the steel plant has always maintained a cautious wait-and-see attitude to maintain stability.