With the continuous development of slurry pump technology, submersible slurry pump has also responded to the market demand. At the same time, this type of pump is especially suitable for the depth where the vertical slurry pump cannot operate. Pay attention when using the equipment. The submersible slurry pump can operate if its depth is less than m, but it exceeds　　Whether the pump is evacuated or overflowed, etc., and handle it at any time.Farhar,　　Fire pump control cabinet generally has two control modes: one is fire hydrant control, and the other is spray pump control. The working principle of the spray pump control cabinet is that the pressure controller is designed with a normally open contact. When the pressure relay acts due to the pressure difference, the control circuit moves the main circuit　　Friction. Because if the surface of the pump is smooth when it is used, the equipment will consume less energy when it is used. Generally, the submersible slurry pump and impeller are sprayed with polymer composite materials for useMachachi,　　Compared with the vertical slurry pump, the application market is also larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping on board, prospecting, etc; Submersible slurry pump assembly workshop III. what are the advantages of submersible slurry pump　　The of descending axial force can be used for slurry transportation in power plants, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min,FarharFire deep well pump, which is mostly used to transport flammable, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature,FarharVertical multistage centrifugal pipeline pump,FarharDeep well pump, high pressure and low temperature.　　The high-efficiency slurry pump has three characteristics: first, the slurry pump has high operation efficiency and low loss.

　　 bind the exposed copper wire to the cable core evenly, and infiltrate tin evenly.　　The impeller channel reaches the outer edge.　　If the pump outputs more medium liquid it will certainly do more work. If it sends less water, it will certainly do less work, and the current will be correspondingly reduced. Pump power (kw) = head (m) × Flow (m/s) × The gravity of the fluid (kg/m for water) divided by (power conversion factor) divided by the efficiency of the pump (aboutHonest service,　　According to the user&#;s requirements, the motor can add a variety of protection devices such as water inflow detection and overheating so that the product can operate safely for a long time under adverse working conditions.　　So it is called: submersible slurry pump.　　Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop, and tighten the two dust discs and fasten them on the shaft. adjustment

　　The supply of shaft seal water must be ensured. It is strictly prohibited to operate without water, otherwise the mechanical seal will be burned.Executive standard, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in addition　　I believe you have such a question when using the submersible sewage pump, that is, is this pump a submersible pump? Or is it a sewage pump? In fact, this question is very easy to distinguish. You can take a look at the following contents sorted out by Shanghai Shenquan.　　The input quantity is related to many factors such as the rotating speed of the submersible slurry pump, the bearing standard, the continuous working time, it is necessary to gradually accumulate the experience and add smooth oil in a reasonable and timely manner.Farhar the surrounding environment and the working temperature. Therefore,　　At present, mechanical seals occupy an increasing share in the slurry pump seal market.　　 If it is found that the impeller is damaged and the liquid supply is insufficient, it is necessary to replace the new impeller in time for use.　　 In addition, the noise method directly detects the noise of the equipment in the detection process, but this measurement will also be affected by the surrounding noise, so in fact, this measurement is not very accurate.