. Raw material problem of stainless steel pipe. If the hardness is too low, it is not easy to polish (BQ is not good). If the hardness is too low, orange peel is easy to appear on the surface during deep drawing, which affects BQ performance. BQ with high hardness is relatively good.Assembly: the sealing ring shall be correctly installed in the U-groove of the pipe fitting, put the pipe into the socket of the pipe fitting and wait for crimping.Phoenix, after deep drawing, small black spots and RI high imitation dging will also appear on the surface of the area with large deformation, which will affect the BQ attribute.The back is blocked with blocking plate for ventilation protection; Only soluble paper or the combination of soluble paper and blocking plate is used for blocking ventilation protection; Use flux cored wire for backing TIG welding.Lamphun, the process of ventilation in advance and gas stop behind shall be adopted, it is not easy to be damaged, so this welding can well ensure that the inner side of the weld is filled with argon and its purity, so as to effectively ensure that the metal on the inner side of the weld is not oxidized and ensure the quality of weld backing welding.Rheological and thermal changes in the quenching process of decorative stainless steel pipe the cooling characteristics of submerged quenching of stainless steel plate are numerically simulated by using the Euler multi fluid model in AVL fire software, and the numerical results are compared with the experimental results. In the research, the quenching medium is water. The mass, the temperature field of quenching medium and workpiece is solved by coupling. The comparison between the numerical simulation and experimental results of decorative stainless steel pipe shows that the numerical simulation results of workpiece temperature are in good agreement with the experimental data. The model can reliably simulate the quenching process of workpiece, and can be extended to the multiphase flow simulation in complex system to guide the actual production. The single pass thermal simulation compression experiment of Cr super martensitic stainless steel was carried out by Gleeble thermal simulation tester to study the thermal deformation behavior at ~ ℃ and strain rate of . ~ s-, and the microstructure evolution law of grains under different conditions was analyzed; Based on Sellars hyperbolic sinusoidal model the flow stress constitutive equation of Cr super martensitic stainless steel was constructed. The results show that the peak stress decreases with the increase of deformation temperature and the decrease of strain rate; With the increase of deformation temperature, the grain grows and coarsens gradually. With the increase of strain rate, the dynamic recrystallized grains are obviously refined. The thermal deformation activation energy Q = . JMOL of decorative stainless steel pipe is calculated, and the expression of Zener Hollomon parameter is obtained. Different feedstocks were prepared by mixing crmnmon nickel free austenitic stainless steel powder prepared by aerosol and wax based binder. The effects of binder ratio and powder loading on the rheological properties of feed were studied by rh high pressure capillary rheometer. Non Newtonian index n, viscous flow activation energy E and comprehensive rheological factor alpha are calculated by second order model regression analysis; STV. The results show that the prepared feeds are pseudoplastic fluid. The binder system was composed of % microcrystalline wax (MW), % high density polyethylene (HDPE), % ethylene vinyl acetate copolymer (EVA) and % stearic acid (SA). The powder loading was vol%. The feed had good comprehensive rheological properties. In order to study the cementitious properties of stainless steel AOD slag, stainless steel AOD slag was used to replace some cement, and its effects on the working properties and mechanical properties of cement mortar were studied. The results show that using stainless steel AOD slag to replace cement from ~ %, with the increase of the content of stainless steel AOD slag, the water consumption of standard consistency of cement first decreases and then increases. When the content is %, the water reduction effect of stainless steel AOD slag is good; With the increase of the content of stainless steel AOD slag, the strength of cement mortar decreases in turn, indicating that the cementitious activity of stainless steel AOD slag is small.Stainless steel pipe factory stainless steel products are widely used in hardware products, furniture, mechanical structure, mechanical accessories, precision medical instruments, fluid transmission pipelines, such as furniture machinery, medical oil, natural gas water, gas, steam and other industries.

Formula for hydraulic test pressure of stainless steel welded pipe for weight calculation fluid (gbt-): where: P - test pressure, MPa; R - stress, taking yield point of %, mm; D - Nominal outer diameter of steel pipe, mm.The thickness of cold rolled steel strip is ultra-thin, and the thickness of hot rolled steel strip is large.First of all,PhoenixPrice of stainless steel strip, let's understand what stainless steel is. Generally speaking, steel that will not rust is called stainless steel, but in an academic sense, steel resistant to weak corrosive media such as air, steam and water and chemical corrosive media such as acid, alkali and salt. Also known as stainless acid resistant steel. In practical application, the steel resistant to weak corrosion medium is often called stainless steel, while the steel resistant to chemical medium is called acid resistant steel. Due to the difference in chemical composition between the two, the former is not necessarily resistant to chemical medium corrosion, while the latter is generally stainless. The corrosion resistance of stainless steel depends on the alloying elements contained in the steel. Chromium is the basic element for stainless steel to obtain corrosion resistance. When the chromium content in the steel reaches about %, chromium reacts with oxygen in the corrosive medium to form a thin oxide film (self passivation film) on the steel surface, which can prevent further corrosion of the steel matrix. In addition to chromium, the commonly used alloy elements include nickel, molybdenum, titanium, niobium, copper, nitrogen, etc., so as to meet the requirements of various uses on the microstructure and properties of stainless steel.How much does it cost?,Corrosion resistance of decorative stainless steel pipe the price of different series of stainless steel materials varies greatly. The corrosion resistance of more economical materials can not meet the higher application requirements, and the improvement of corrosion resistance of stainless steel materials by simple chemical passivation is limited. On the other hand, the traditional passivation treatment containing chromium salt has been gradually eliminated, and the passivation treatment of stainless steel has turned to the direction of environmental friendliness. Recently, citric acid passivation and silicon treatment on stainless steel surface have become a new research direction. The former has environmental protection characteristics because its passivation solution component does not contain chromium salt. The latter has found that silicon coupling agent is chemically adsorbed on the metal surface to form a protective silicon film with cross-linked network structure. The length of discoloration time of samples after different surface treatments was compared by blue dot method, the corrosion rate of samples after different surface treatments was distinguished by brine immersion test, and the salt spray resistance of samples after different surface treatments was distinguished by neutral salt spray test, The differences of pitting corrosion resistance and resistance to corrosive medium of samples after different surface treatment were compared by electrochemical test. The film thickness of silicon film was indirectly characterized by film weight test, and scanning electron microscope, energy spectrometer, X-ray diffraction X-ray photoelectron spectroscopy and total reflection Fourier transform infrared spectroscopy characterized the surface films of different surface treated samples, and analyzed the structural composition and corrosion resistance mechanism of different films. Professional stainless steel plate, stainless steel coil, stainless steel belt, stainless steel pipe, high price, service, on-site settlement, honest management! At present, there are few studies on the combination of citric acid passivation and silicon treatment of stainless steel. Therefore, this paper studies the difference of corrosion resistance of martensitic stainless steel Cr chemical passivation, silicon treatment and the combination of citric acid passivation and acid silicon system treatment, which can provide reference for the new direction of stainless steel surface treatment, It has certain practical guiding significance. The corrosion resistance and mechanism of chemical passivation, silicon treatment and composite treatment of martensitic stainless steel were studied in this paper. The comprehensive comparison of the research results shows that the corrosion resistance of stainless steel treated with different surface treatments is different. The corrosion resistance of the sample treated with silicon alone is better than that treated with traditional dichromate passivation. The corrosion resistance of the composite treated sample treated with citric acid passivation and acid silicon system is further enhanced than that treated with acid silicon system alone. The composite treatment of citric acid passivation and acid silicon system treatment has excellent corrosion resistance and environmental protection characteristics, and is expected to replace the traditional dichromate passivation treatment. According to the film weight test results, indicating that the excellent corrosion resistance of the composite film not only depends on the surface silicon film, but also benefits from its double-layer film structure.In the interior decoration project, the proportion of water pipes is very small, whether it is data consumption or price. However, once the water pipes show achievements, the results will be very serious. Therefore, it is extremely important to choose water pipes with reliable quality, high volatility, convenient maintenance, people's requirements for domestic water pay more and more attention to health and environmental protection. A good water source escort pipeline has become a careful choice. Water pipes are generally experienced in lead pipes & rarr; Copper pipe & rarr; Iron pipe & rarr; Galvanized iron pipe → Plastic pipe & rarr; Development process of stainless steel pipe. It has become a trend in the world to select high-quality stainless steel materials as water supply pipes. The material indicates that in Germany, more than % of residents choose stainless steel water pipes; In Japan, more than % of households in Tokyo have adopted stainless steel water pipes; In Australia, it has begun to change other pipes to stainless steel pipes; In the United States, the water pipes of five-star hotels in Las Vegas are all made of stainless steel. Since the beginning of the st century, due to the progress of living standards, more than % of residents in China need water pipes to meet their needs of high-quality life. Therefore, high-quality stainless steel materials move from tableware to household water pipes. It has become a trend to select high-quality stainless steel pipes in tooling or home decoration projects. Stainless steel water pipes and stainless steel pipe fittings will become an indispensable part of the building materials market in the future. Stainless steel material is a recognized health material that can be implanted. The manufacture of water pipes based on stainless steel has a long history in developed countries. Stainless steel pipe has gradually become a new choice of water supply pipe with the characteristics of safety, sanitation environmental protection,PhoenixWhere is stainless steel plate 304, economy and applicability and has become the current world trend and development direction. Stainless steel water pipe is called the real green pipe in the st century. With the gradual standardization of stainless steel pipe industry, it can be predicted that the consumption technology and connection technology of stainless steel pipe will also slow down to standardization and become more and more perfect. The development of stainless steel pipe technology will not only create a favorable condition for health, environmental protection and sanitation for national domestic water, but also win a larger market for stainless steel pipe enterprises. Stainless steel pipe entering the construction and decoration market is an attack in the water pipe industry.Stainless steel pipe cost = actual thickness divided by thickness adjustment price + freight + processing fee. Coil price is switched to flat plate price = coil price, actual thickness adjustment + leveling fee . Flat plate price is switched to coil price = plate price, thickness adjustment - leveling fee . Coil length = coil net weight . Coil width. Actual thickness including tax price algorithm = total weight of goods ( represents points, is points)

In engineering, the following methods are often used to prevent intergranular corrosion: reduce the amount of carbon in steel so that the amount of carbon in steel is lower than the saturated solubility of austenite in equilibrium, fundamentally solve the problem of precipitation of chromium carbide (crc) on the grain boundary. Generally, the requirement of intergranular corrosion resistance can be met when the amount of carbon in steel is reduced to less than .%.Customer first,As long as the steel type is selected correctly and maintained properly, stainless steel will not produce corrosion pitting, corrosion or wear. Stainless steel is also one of the high-strength materials in metal materials for construction. Because stainless steel has good corrosion resistance, it can ensure that the structural components can maintain the integrity of engineering design. Chromium containing stainless steel also integrates mechanical strength and high extensibility and is easy to wear The processing and manufacturing of parts can be fullThe folded stainless steel hot rolled strip is hot rolled into a strip with a thickness of mm-mm and a width of mm-mm.At low temperature, ferritic stainless steel pipe has low-temperature brittleness like carbon steel but austenitic steel does not. Therefore, ferritic or martensitic stainless steel produces low-temperature brittleness, while austenitic stainless steel or nickel base alloy does not show low-temperature brittleness. Sus (Cr) and SUS (cr) of ferritic stainless steel pipe It shows that the impact value decreases sharply at low temperature. Therefore, it is necessary to pay special attention when using at low temperature. As a way to improve the impact toughness of ferritic series stainless steel, high purification process can be considered. With the help of C and N level, the embrittlement temperature is in the range of - ℃ to - ℃Phoenix,PhoenixStainless steel strip 316L,Austenitic stainless steel is generally used for manufacturing and manufacturing chemical equipment components, low-temperature equipment components in refrigeration industry, and can be used as stainless steel spring and clock spring after deformation strengthening.The back is blocked with blocking plate for ventilation protection; Only soluble paper or the combination of soluble paper and blocking plate is used for blocking ventilation protection; Use flux cored wire for backing TIG welding.Model & mdash; The corrosion resistance is the same, and the strength is better because the carbon content is relatively high.