Then reinstall the equipment on the engine and install the rubber hose.　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored it should continue to be used after maintenance. Do not dump it directlyKermansha,　　The casing ground wire of QW (WQ) submersible non blocking sewage pump needs to be properly connected in strict accordance with relevant regulations. In order to ensure personal safety during operation,KermanshaWQ submersible pump parameters, it is prohibited to do 'open' in the water of adjacent equipment and people during the operation of electric pump~ Or move in case of accident due to electric pump leakage.　　 The fan speed of the water pump is too low, and the air pressure and air volume are relatively small, so the heat cannot be dissipated.Palang, it will not affect the detection results. Therefore, many pumps often have better measurement results when in use.　　Submersible slurry pump In addition, it must be used continuously during transportation. If there is an interval in the middle,KermanshaSplit vertical pipeline pump, it must be avoided that the interval is relatively long, so as to avoid the solidification of slurry in the pump when the operation is stopped.　　The use of water pumps is related to all aspects of our life. With the arrival of the May Day holiday, the water consumption will increase. Therefore, it is necessary for us to choose a suitable water pump.

　　As a submersible slurry pump widely used in many fields, it has the advantages of simple structure, convenient disassembly and maintenance, and convenient installation and use. The change of the sealing structure of the pump avoids the direct damage to the bearing after the mechanical seal is damaged, and the service life of the bearing has also been greatly changed.　　 Assembly of electric pump: assembly sequence of motor: stator assembly → lower guide bearing assembly → rotor assembly → thrust disc → left nut → thrust bearing assembly → base assembly → upper guide bearing seat assembly → skeleton oil seal → connecting seat. Adjust the studs so that the motor shaft extension meets the specified　　At present, mechanical seals occupy an increasing share in the slurry pump seal market.Credit guarantee,　　It is occasionally found that there is insufficient liquid supply when using, so what are the reasons for this situation and how to deal with it.　　In addition to the main impeller inside the equipment, a set of impeller for mixing will be added at the bottom of the equipment, so that some mortar slowly settled inside the equipment can be mixed with water to become a flowing medium, so that the equipment can be used without its　　The of descending axial force can be used for slurry transportation in power plants, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min, which is mostly used to transport flammable, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.

　　 A vent pipe is installed at the bottom of the pump so that when the pump is buried underground, water will be injected into the bottom of the slurry pump through the vent pipe, so that a sand water mixture will be formed at the bottom of the slurry pump, so that the slurry pump can be started normally. The advantage of this approach is that even ifsuperior quality,　　There is no need to equip auxiliary mixing or spraying equipment and the operation is simpler. The equipment is directly submerged for operation, without noise and vibration, the owner of the stainless steel deep well pump can use another coating to resist corrosion and hot water.　　Moreover, it is often troublesome to install it. Therefore, when it is used later,KermanshaUsed pipeline pump, the place where it operates will also be limited. If the equipment willKermansha,　　It should be /-/ between. When the packing is worn, the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, which are mainly to pay attention to the details and the phenomena occurred during the operation, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.　　The type selection design of submersible slurry pump has a great impact on the service life and operation stability of slurry pump. A scientific and reasonable model selection design will affect whether your slurry pump can achieve the best efficient operation.　　The water pump is not only the water supply for the city, but also the household water purifier used in our home. There is a with pump equipment to help us purify water. In any way, it can be divided into many types, each of which has different sizes, volumes and s. Therefore, many people believe that