Then look at the quality Keep the floor dry and clean. If there is dirt on the floor surface, generally wipe it dry with a damp mop without dripping water.Osterhoot,SPC floor has a thickness of mm-mm, and the weight per square meter is only about -kg, which is less than % of ordinary ground materials. It has incomparable advantages in building load-bearing and space saving in high-rise buildings.At the same time, it has special advantages in secondary decoration and transformation.The real wood floor is processed with a whole plate, with natural texture, and its section texture can correspond to the surface texture one by one;Fake solid wood floor is mostly pasted with leather or stickers on the fake floor, so the cut texture is not commensurate with the surface texture.People who have a certain understanding of the manufacturing process of composite wood flooring should know that adhesive is essential, but the whole process of SPC flooring is not adhesive (adhesive releases formaldehyde at high temperature), environmental protection. The real formaldehyde is quickly distinguished from many wood flooring materials, and is more and more loved and used by owners.However, it does not refer to formaldehyde, but refers to that the formaldehyde emission is less than .mg/l, and the harm is small.

Defects.In another case the scar is deep, colored with paint repair pen, and then polished.Needless to say, for a long time, the lacquered cloth market was occupied by low-grade unlined lacquered cloth produced in Taiwan and other overseas countries, giving consumers the wrong message that China&#;s quality is not up to standard. In fact, after the inspection of these, the surface wear-resistant layer is only .mm, which is made of poorly processed and Recycled PVC. It does not meet the national standards for plastic coiled materials at all, so its service life is short, not comfortable to use.Sampling inspection,quality Ultra light and ultra-thin, SPC floor has a thickness of about mm-mm and light weight, which is less than % of ordinary ground materials. It has incomparable advantages in stair bearing and space saving in high-rise buildings. At the same time, it has special advantages in the reconstruction of old buildings.The wear resistance of laminate floor mainly depends on the content of aluminum oxide in the surface layer, and a certain number of wear-resistant revolutions corresponds to a certain content of aluminum oxide.For household floors, the number of wear-resistant revolutions is usually more than revolutions, while in public places, it is usually more than revolutions. You can buy it on demand.

easy careranking, blocks, plates or coils can be selected.Floor lacquer cloth, is a kind of paving material. It belongs to rubber plastic products. It is one of the indispensable floor materials for the decoration of power distribution room, substation and communication room. The thickness is -mm. Other thicknesses can be made according to the needs of users. The wear-resistant layer is generally less than or equal to .mm.The choice of lacquer cloth products shall be selected according to the suitability of the site.For example, the size of the product is determined according to the space of the house and the size of the place of use.At the same time, pay attention to the different places of use, and the selected patterns should also be different.For example, in places that need to be kept clean, you can&#;t choose products with convex effect;In solemn places, it is not suitable to choose products with bright colors and messy.The width of coiled floor paint cloth is mm,OsterhootHow much is the floor per square meter, mm and mm;The total thickness (referring to the base material, intermediate layer and surface wear-resistant layer) is divided into mm and mm;The length of each roll of floor leather is m and m.Other specifications and dimensions can be determined by the supplier and the buyer through negotiation.Because of the requirements of production, each roll of floor paint cloth is divided into several sections (the patterns between each two sections are misplaced), so the length of the small section of a roll of floor paint cloth with sections shall be indicated, and the length of the roll of floor paint cloth shall be increased by at least cm (i.e. not less than two complete patterns).Generally, there can only be one section for high-quality products, and the number of sections of each volume of first-class products and qualified products shall not exceed ;The length of each section of first-class products shall not be less than m, and the length of each section of qualified products shall not be less than m.When inspecting the appearance quality of floor paint cloth leather, it should be visually inspected obliquely under the scattered sunlight or fluorescent lamp with the illuminance of ( ± LX and LM away from the tested sample.First observe whether there are cracks, it can be determined that the floor leather is unqualified.The second step is to observe whether there are wrinkle marks, bubble pollution points and pattern deformation. What cannot be observed are excellent products and first-class products;If it is slight but not obvious, it is deemed as qualified. Go back to the third step to observe whether there are missing patterns on the surface of the floor leather and whether there are defects of the transparent wear-resistant film on the surface. If there is no, it is the first-class product and the first-class product. If there is slight missing or lack of film, it is the qualified product, otherwise it is the unqualified product.Finally, carefully check whether there is deviation during multi-color overprint on the surface, whether there are color differences in different parts, whether the superior products are uneven,OsterhootFloor rubber board and floor leather, and if there are the above two defects, the first-class products are those with but not obvious, and the products with obvious above defects but do not affect the overall beauty are determined as qualified products.Finally, based on the above judgment, the appearance quality of ground lacquer cloth is determined.The plastic coil floor paint cloth shall roll the wear-resistant layer outward on the pipe core and shall be externally packaged.The product name, manufacturer name,OsterhootHow to lay floor leather, product mark, grade, batch number, quality and length shall be marked at the obvious place of each package.In addition to the above three items that can be directly judged by the senses, attention should also be paid to the physical properties when purchasing floor leather to ensure its service life. Consider environmental protection factors.The general specification and model of general floor is cm×cm, the specification and model of high-capacity floor can reach cm×cm with a total area of times that of the general wooden floor.The floor is generally made of common materials such as red sandalwood and Huanghua pear wood. The corner material is discarded and made of a key part of the whole tree. It mainly shows the air. The road construction has an endless sense of flexion and extension and three-dimensional feeling.Osterhoot, break the floor and look at the substrate inside. There are no impurities in the good substrate and the color is relatively pure. A large number of impurities can be seen with the naked eye in the poor floor substrate.Most domestic floors use fast-growing forestsLook at the substrate and wood has been used since to years. However, imported floors, especially FSC certified plates, have strict restrictions on wood species, so wood base materials are better. Good wear resistance and stabilityThe flame retardant grade is B, and the formaldehyde concentration is acceptable.Precautions for solid wood floor installation : prevent uneven ground.