Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain, and the maximum load is about tons. .When installing, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing clearance is suitable.Schigerzent michlos,Hydraulic lifting freight elevator, cargo elevator, is mainly designed for transporting goods, usually accompanied by people. The freight elevator car has the characteristics of long and narrow. A vertical lift powered by an electric motor, fitted with a box-like gondola. Fixed lifting equipment serving specified floors. It has a car that runs between at least two vertical columns of rigid rails. Let's take a look at its daily maintenance skills: Daily maintenance skills for hydraulic lifts The newly installed hydraulic lifts first have a warranty period from the elevator manufacturer (generally -- years).Test the freight elevator every day to see if the freight elevator can operate normally.Nanjing,Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?The hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type,Schigerzent michlosElevating cargo elevator, car type, auxiliary self-propelled type, and the lifting height ranges from a meter to s meter.Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts, screws, etc. are loose, if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)

Low cost: The cost is much lower than that of the scissor-type mobile lifting platform so when purchasing a lifting platform, you must consider the scope of use of the lifting platform, the frequency of work, the load and other factors to choose a lifting platform that suits the work requirements .The shafts in the middle of the support rods of the hydraulic lifting platform are inconsistent, causing the lifting platform to fail to work normally, the platform is severely damaged, and the table is tilted. Please check carefully that the general scissor aerial work platform has not been strictly tested before leaving the factory, and it has been put into the market. Caused a lot of accidents to take place, for the tilt detection, the detection of this link is not very concerned about for the majority of small enterprises, which is why there are such a large number of lifting equipment to have this problem. Problems with the oil cylinder and the power unit system are often caused by insufficient power and unqualified quality of the oil cylinder, which is also a problem that the enterprise itself needs to pay attention to.The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.NowadaysIf the motor of the hydraulic lift is overheated, small and medium-sized enterprises are holding products with the idea of ​​good quality and favorable price.The safety device and application of the guide rail hydraulic lifting platform The use of the guide rail hydraulic lifting platform The guide rail hydraulic lifting platform is a non-scissor hydraulic lifting freight elevator. It is used for goods between different floors of industrial plants, restaurants, restaurants, etc. The low height can be made to -mm. The advantage is that it can be placed directly on the ground without digging pits, reducing engineering construction costs, and there is no need to set up hanging points on the top, which is safe. Reliable; the hydraulic lifting platform adopts hydraulic transmission mode, or one of the parallel branches is disconnected, the three-phase current will be unbalanced and the motor will overheat.

It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V,Schigerzent michlosFixed lifting hydraulic cargo elevator, if you touch the power supply with your hands, it may cause lifting failure in light cases, or electric shock accidents in severe cases.ranking,Ensure good power supply at the installation site, install a separate distribution box and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .Pay attention to heat dissipation when the motor works in a hot environment.Mechanisms: Mechanisms such as tabletops, track grooves, wire ropes, chains, and pulleys are made of solid materials to ensure safety.Schigerzent michlos,Always check the connections of the various parts of the hydraulic lift, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.Many people think that the strength of the elevator itself is relatively high when using the elevator, but they do not know that this will cause increased wear and tear of the parts and inflexible operation, and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation, use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore, when you install the elevator, please be sure to strictly follow the installation and use related matters below, and assemble and use it carefully.Secondly, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box,Schigerzent michlosBody guide rail type cargo elevator, gearbox, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found, replace them in time. If there is any looseness, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, whether the motor is overheated, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor each box, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.