The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.　　 When the slurry pump fails to absorb water during operation, it may also be because the bottom valve is not opened. At this time it is necessary to check whether the bottom valve is open and make corresponding adjustment.Japan,　　The equipment of this series of sewage pumps can be fixed or mobile. When the fixed active equipment is selected, the chain cable shall be separately threaded into (against the pump outlet, and its connection shall be parallel to the pump outlet) two eyebolts or lifting plates to lift the electric pump up and down. Evenly and slowly along the guide rail　　 Why does the demand for submersible slurry pumps increase greatly? From the perspective of market demand, although the number of submersible slurry pumps has not exceeded that of vertical slurry pumps, the application market of submersible slurry pump is also better than that of vertical pumpBeveren,　　Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop, and tighten the two dust discs and fasten them on the shaft. adjustment　　 Pipeline layout: Firmly support the water pipe and drain pipe to prevent the force of the pipe from acting on the submersible slurry pump.　　 The fixing method of the impeller is changed from screw thread to key clamp to prevent the impeller from falling off and causing damage!

　　 the water pipe shall be short, and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.　　 After the electric pump has been used for many times, it is necessary to put the electric pump into clean water and run it for several minutes to prevent sediment in the pump and ensure the cleanness of the electric pump.　　 We must choose to consider the actual use situation when making the selection, because there will be some difference between the marked head when using and the head when using. This is because the pipe itselfCredit guarantee, this is a very common phenomenon. You don&#;t have to worry about it. Water pump can transport many things, such as water, oil, liquid metal, acid-base night and so on. It is a good means of transport.　　Circumference. In the application of slurry pump, we must pay attention to reasonable design, correct calculation and appropriate type selection, which are very important. In addition to the main wheel, a set of stirring impeller is added at the bottom of the product, which can spray the precipitated slag into a mixture of water and solid particles

　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakageinstall,　　When the submersible slurry pump is used at ordinary times, cavitation usually occurs, which has a great impact on the impeller of the equipment itself. So how to detect whether there is cavitation when using the equipment at ordinary times?　　If there is a gap in the actual work, if the pipeline can not absorb water normally, it is necessary to find out whether the model of the pipeline pump can have the self-priming , and then check the cause of the abnormal suction range of the pipeline pump and solve it.　　Pump, sewage submersible pump and seawater submersible pump.Japan,JapanWater well pipeline pump,JapanSubmersible sewage pump,JapanFire deep well pump,　　 drainage and water injection with vacuum equipment: the self exhaust of centrifugal pump is the same as the negative pressure exhaust of vacuum pump, so the water ring vacuum pump is used for exhaust to achieve the of water inlet.　　Be sure to choose a pump that is more suitable for use.　　Many users including new practitioners of slurry pumps, often fail to distinguish the difference between submerged vertical slurry pumps and submerged slurry pumps. The names of submerged and submerged slurry pumps seem similar, but there are essential differences. What is the difference between submersible slurry pump and vertical slurry pump?