The lifting stage can provide real-time information on the operation of the entire vehicle, avoiding relying solely on the experience of operators to coordinate with each other, and improving the reliability and safety of the system. The definition of safety zone is very important because the lifting stage has a large range of movements, and it must be accurately calculated. The lifting stage has two structurally separate systems, the ground turntable and the high-altitude work bar. However, for various movements on the vehicle, it is also an interconnected system, which needs to consider the priority of operation, system redundancy, and safety assurance of actions.Please refer to the instruction manual for the maintenance and maintenance of the elevator to check the braking torque of the brakeXingtai,Drivers should be responsible for supervising the uniform distribution of items transported by the platform on the platform as much as possible to prevent partial loading and prohibit overloading. Platform does not allowCheck if the usage period of the speed limiter has expired. If it exceeds the usage period,Lifting and lowering　　?? Hidden danger investigation relies on joint efforts from all aspects:?? Construction enterprises are the main responsibility for identifying hidden dangers in construction elevators. They should strengthen daily inspections and regular inspections, safety protection devices, electrical devices, and transmission devices of construction elevatorsQuarterly maintenance: Check the items checked each month

Attention: Abnormal meshing of gear teeth should be avoided: uneven rolling of the rollers should be avoided; Avoid diagonal orientation of the guide rollers; It should be avoided that the guide rollers are kept at the same time for a long time; The above abnormal phenomena can lead to rapid wear and even scrapping of gears, racks,XingtaiRail type cargo lifting platform, rollers, and guide rails. If adjusted more carefully, it will be more beneficial for the service life of the elevator.The vibration frequency should be set to obtain large dynamic stress with low energy consumption, and the resonance frequency should be used to handle time dependent vibration. However, there may be one or more resonance peaks in large components, and using resonance peaks with higher peaks and lower frequencies for aging can achieve optimal results. The resonance frequency needs to be determined by trial vibration, which slowly increases the speed of the excitation motor from and determines the relationship curve between the amplitude of the workpiece and the motor speed to determine the resonance point of the workpiece. According to the scanning curve, a large acceleration was obtained at r/min, so r/min was determined as the aging frequency.What are the functions of anti rust primer for warehouse cargo elevators?Installation conditions,Since the antirust paint on the exterior layer will actively react with the oxygen in the air, especially in the cold sun or rainstorm climate, the reaction speed will be accelerated, so the exterior paint on the warehouse goods elevator will show signs of aging and then fall off every once in a while. Therefore, when maintaining the equipment of the lift table at ordinary times, pay attention to its storage, and try not to leave it outdoors, let alone in cool days or rainstormOn the contrary, it should be adjusted in the opposite direction; When the meshing backlash of the gear pair is greater than .mm,XingtaiMobile hydraulic boarding bridge, loosen the connecting nut of the eccentric shaft of the guide roller and the tooth back pressure wheel as shown in ,XingtaiMaintenance of aluminum alloy hydraulic lifting platform, adjust the tooth back pressure wheel to press towards the back plane of the gear rack until the backlash reaches a reasonable range. Otherwise, it should be adjusted in the opposite direction. At this point the guide roller should be loosened for o and then adjusted according to the adjustment of the guide roller.Check the smooth steel wire rope and various fasteners, if there is excessive wear, it is necessary to replace them

With the continuous development of the economy, meeting the needs of society, and increasing productivity, hydraulic cargo elevators play an important role in high-altitude operations. Hydraulic cargo elevators operate up and down, and can provide us with a safe and stable platform. We can provide security for our safety when working at heights.details,Check the interlocking equipment, up and down travel, and other safety maintenance switches of the cage door and fence doorThe arrangement of vibration points should be based on the vibration aging process standard GB/T-. The vibration aging exciter should be placed at a position with high rigidity and amplitude of the workpiece, so that small energy can be used to excite the component with large amplitude. Based on the structural shape of the foundation, we set the vibration points on the protruding plates on each side of the workpiece.Check the interlocking equipment, up and down travel, and other safety maintenance switches of the cage door and fence doorXingtai,Regularly check whether the operation of each mechanism is normal and whether there is any noise. If any faults are found, they must be promptly eliminated.All connecting shafts must have split pins and be sufficient.A non scissor type hydraulic lifting mechanical equipment used for transporting goods between floors of industrial factories restaurants, environmentally friendly, and economical! Our products are exported to foreign countries and highly trusted