Stimulating effect.Related questions edit voiceGotzedelchev, Rich colors and patterns.Floor leather (also known as coiled floor), a new type of flooring material, belongs to plastic products. It is one of the indispensable floor materials for modern room decoration. It has a thickness of more than mm and a wear-resistant layer of more than . Generally, glass wire with good flatness or double primer is used.Plastic floor leather belongs to soft floor. It is a floor roll produced by coating or calendering on sheet continuous substrate with polyvinyl chloride resin as the main raw material and appropriate additives.Advantages of floor leatherOstrava, One week later,GotzedelchevTop 10 laminate brands, the floor sank to the bottom, and the color of the water turned yellow and black. The water contained a lot of impurities SmellDefects: some indoor formaldehyde is restrained, the quality of the sales market is uneven, and most plates are shoddy.

More accurately SPC floors with obvious pungent smell should not be environmentally friendly.SPC rural grass-roots raw materials themselves do not contain indoor formaldehyde. The qualified SPC floor should be . There is no formaldehyde release. It is likely to have the taste of air fragrance and modifier. It is not easy to cause harm to everyone&#;s body and make people feel uncomfortable.Although the installation method of SPC latch floor is the same as that of wood floor, the grasp of details in the installation process is also different from that of wood floor.According to the current market survey, the SPC lock floor of different brands will have edge warping, arching, large expansion joints, and even lock fracture after paving on individual sites. The ground shall be free of water seepage and moisture. Defects.reform,The floor paint cloth is easy to age under the action of light and heat, the floor is hard and the surface color changes, daily maintenance and maintenance are also very important. First keep the board surface clean and free of sand and dust friction on the board surface; prevent pollutionThe objects shall be removed in time. Pay attention not to scrub with aone, cyclohexanone, concentrated alkaline water and other organic solvents to prevent color fading, degumming, cracking or warping of the surface. They can be wiped with detergent or detergent. They shall be cleaned with semi dry mop on weekdays to prevent dirty water from penetrating into the joint and damaging the bond.Stable, teak is the best, followed by two winged beans, passionfruit round beans, etc., and then oak.In fact, such as wear resistance, water resistance, pollution resistance and flame resistance,GotzedelchevTop ten famous brands of composite flooring, are improved with the hardness of floor leather.Therefore, expert Construction: when purchasing floor leather, as long as the surface meets the wear-resistant requirements, there is no need to demand softness, so as to facilitate the comprehensive improvement of other properties.Floor lacquer cloth (also known as floor leather and insulating floor rubber roll) is one of the indispensable or missing floor materials for the decoration of modern power distribution room, substation and communication room. It is not only beautiful and practical, but also has the characteristics of sound and moisture insulation, wear resistance and corrosion resistance. It can be used not only on the floor of living room, but also on the floor of workshop.The ground of the weak point machine room.Gotzedelchev, bright as a new mouth, no stains, easy to clean.The surface paint of solid wood composite floor is very good, with good wear resistance, without excessive vitality maintenance.According to statistics, the solid wood composite floor prepared for the sales market will not be waxed within years, and the wind color of automobile coating will also be maintained.This is obviously compared with the maintenance of solid wood flooring.Impregnated paper laminated wood floor is a floor made of one or more layers of special paper impregnated with thermosetting amino resin, which is paved on the surface of wood-based board substrate such as particleboard and high-density fiberboard, with a balanced moisture-proof layer on the back and a wear-resistant layer and decorative layer on the front. It is hot pressed and formed. First, it is divided into thin and thick (more than mm and about mm in thickness).The laminate floor is composed of wear-resistant layer, decorative layer, base material and balance layer.The wear-resistant layer, decorative layer and balance layer are manually printed and the base material is made of fast-growing forest materials. The cost is lower than that of solid wood flooring. At the same time, it can be produced on a large scale, and the relative cost performance is high.Due to the different base materials, the price difference is obvious, and there is more room for customers to choose, which is suitable for people at all levels.