The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today, the editor will give you a popular science.San Francisco,Now you understand how to use the hydraulic lift. It provides our operators with a safe working environment and improves the working efficiency and quality of the lift.The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.Melbourne,Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, this will hide the moisture. Therefore, the outer edge of the wheel hub, the door, the corner of the bottom of the trunk, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding, the short-circuit current is much larger than the normal operating current, which increases the copper loss of the winding, causing the winding to overheat and even burn out.The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises, municipal construction,San FranciscoThree story cargo elevator, and decoration of hotels and hotels, with reliable quality and perfect performance.

Features of hydraulic lifts: According to the working mode hydraulic lifting platform products are divided into crank arm hydraulic lifting machines, scissor hydraulic lifting machines, mast type hydraulic lifts, and straight arm hydraulic lifting machines. The hydraulic lift is a replacement product of the folding arm lift (lifting platform) and the scissor lift (lifting platform). It can be widely used in stations, docks, airports, hotels, post and telecommunications, municipal gardens, garages, cleaning companies, public building facade decoration, decoration or installation and maintenance of power systems, etc. The lift has the advantages of light weight, self-propelled, electric start, self-supporting legs, simple operation, large working area, especially the ability to cross obstacles for high-altitude operations and the like.It is strictly forbidden to use the seat belt to transfer heavy objects; the seat belt should be hung on a firm and reliable place above, and the height of the seat belt is higher than the waist. The professional elevator factory is safe, environmentally friendly and economical! The products are exported to foreign countries and are deeply trusted.Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain with strong stability and high carrying capacity. The maximum lifting height is about meters,After the goods are transported clean up the debris on the platform.The scissor-type fixed lifting platform is a kind of transportation and handling equipment for transporting goods from a certain height to another height. After the operation is completed, the platform is level with the ground, does not occupy the ground space, and does not affect the passageway.Many people think that the strength of the elevator itself is relatively high when using the elevator, so they did not strictly follow the installation method in the manual during the installation process, but they do not know that this will cause increased wear and tear of the parts and inflexible operation, and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation, use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore, when you install the elevator, please be sure to strictly follow the installation and use related matters below, and assemble and use it carefully.

Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload, transport flammable and explosive products and other products.Equipment maintenance,Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, this will hide the moisture. Therefore, the outer edge of the wheel hub, the door, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.The shafts in the middle of the support rods of the hydraulic lifting platform are inconsistent causing the lifting platform to fail to work normally, the platform is severely damaged,San FranciscoGuide rail lifting cargo elevator cargo elevator, and the table is tilted. Please check carefully that the general scissor aerial work platform has not been strictly tested before leaving the factory, and it has been put into the market. Caused a lot of accidents to take place, for the tilt detection, the detection of this link is not very concerned about for the majority of small enterprises, which is why there are such a large number of lifting equipment to have this problem. Problems with the oil cylinder and the power unit system are often caused by insufficient power and unqualified quality of the oil cylinder, which is also a problem that the enterprise itself needs to pay attention to.The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand, it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.San Francisco,The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases, high-strength chrome-plated rods, Japanese NOK seals, self-made external integrated pump stations, oil pipelines, gear pumps, solenoid valves, etc. The Japanese NOK seal used in the oil cylinder has good wear resistance, thereby driving the top of the rod and raising the equipment; The valve is used to adjust the oil output, the ascending and descending speed, and contains an emergency descending device to ensure that the guide rail hydraulic lifting platform can descend safely in case of an emergency.Check the front page of the oil pipe to check whether the skin of the oil pipe of the hydraulic lifting platform is damaged or cracked,San FranciscoBuilding guide rail lifting cargo elevator, replace it immediately; secondly, check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe, and if so, tighten it immediately to avoid lifting on the hydraulic lifting platform There is an oil spill in the process, which leads to accidents; what items need to be checked before using the hydraulic lifting platform? Cut off the power first to avoid tragedies such as electric leakage and electric shock)