physical and chemical properties

In order to make the welded pipe have the required mechanical, in addition to the reasonable selection of materials and forming process, heat treatment process is often necessary. In addition, the mechanical, physical and chemical properties of aluminum, copper, magnesium, titanium and their alloys can be changed by heat treatment to obtain different service properties.Metallization: refers to the process of penetrating metal atoms into the surface layer of alloy steel pipe. It is to alloy the surface layer of steel so that the workpiece surface has the characteristics of some alloy steel. Aluminizing, boronizing, siliconizing and so on are commonly used in production.Makara, Product description of galvanized pipeMain uses: as a finished material, flat steel can be used to make hoop iron, tools and mechanical parts, and used as building frame structural parts and escalators in buildings. Flat steel is divided into two types according to its shape: plane spring flat steel and single-sided double groove spring flat steel. Hot rolled spring flat steel is mainly used to manufacture leaf springs for automobiles, tractors, railway transportation and other machinery.Gibara,MakaraInconel 625 nickel base alloy pipe,According to the national standard of hot rolled H-section steel in China (GB / t-, H-section steel is divided into narrow flange, wide flange and steel pile whose codes are Hz, HK and Hu respectively. Narrow flange H-section steel is suitable for beams or compression bending members,MakaraSeamless pipe manufacturer, while wide flange H-section steel and H-section steel piles are suitable for axial compression members or compression bending members. Compared with H-section steel, W, IX and iy are not as good as H-section steel under the premise of equal weight.In order to make the steel pipe workpiece have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming processes, heat treatment process is often essential. Steel is the most widely used material in the mechanical industry. The microstructure of steel is complex and can be controlled by heat treatment. Therefore, copper aluminum, titanium and their alloys can also change their mechanical,Makara1Cr5Mo high pressure alloy pipe, physical and chemical properties through heat treatment to obtain different service properties. Mixed pass system. According to the characteristics of rolling mills and products, in order to give full play to the advantages of their respective systems and overcome their disadvantages, mixed pass system is often adopted, that is, the combination of more than two systems. For example, straight leg cross rolling pass system is adopted for finished hole and front hole of finished product, etc.

The shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm.They are not affected by surrounding factors and processes, including corrosion. Cold extrusion. This kind of processing method is more purposeful. Before the preparation of steel processing and extrusion molding when the extrusion molding is used for mm diameter pipe fittings, the investment of machinery and equipment is less, so the raw material consumption is also very small, and the technology is relatively perfect. Once the tube size is increased, the cold extrusion method must have large cargo capacity and high-power machinery and equipment. Therefore, the automatic control system will be upgraded.Which one is better,The side length of I-beam is small and the height is large, so it can only bear the force in one direction.At present, there is still a big gap in the production technology of C-section steel between China and foreign countries.The system is mainly composed of control box, finishing roller, pre leveling unit, finishing unit and straightening unit.

The flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.Quality inspection report,It is often asked that the shape of I-beam is similar to that of H-beam. What is the difference between them? Many people can&#;t explain it in detail. Here is a detailed answer for you: many people think that I-beam is a domestic name and H-beam is a foreign name. In fact, this cognition is wrong. H-beam and I-beam are different in shape!Galvanized pipe: the hot-dip galvanized pipe base plate and molten electroplating solution are combined physically and chemically to form a dense corrosion-resistant structure of zinc iron alloy layer. The alloy layer is integrated with the pure zinc layer and the steel pipe substrate. Therefore, it has strong corrosion resistance.H-section steel belongs to high-efficiency and economic cutting profile (other cold-formed thin-wall section steel, profiled steel plate, etc.). Due to the reasonable section shape, they can make the steel give more play to its performance and improve the cutting capacity. Different from ordinary I-type, the flange of H-section steel is widened, and the inner and outer surfaces are usually parallel, so it is convenient to connect with other components with high-strength bolts. Its size composition is reasonable, series and models are complete, which is convenient for settingMakara, Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time, and the waist is parallel to the roll axis.According to the theory of steel structure, the I-beam flange should be stressed, that is, the I-beam should be standing rather than lying down.Dehydrogenation solution: the alloy pipe shall be dehydrogenated after passivation treatment to avoid alkali embrittlement