Austenitic stainless steel has good resistance to uniform corrosion, but there are still the following problems in local corrosion resistance: intergranular corrosion of austenitic stainless steel. Austenitic stainless steel will have intergranular corrosion when it is kept warm at ~ ℃ or cooled slowly. The higher the carbon content, the greater the tendency of intergranular corrosion. In addition, intergranular corrosion also occurs in the heat affected zone of the weldment. This is due to the precipitation of Cr rich CrC on the grain boundary. The chromium poor area is formed in the surrounding matrix,DavintelStainless steel pipe size, which is caused by corrosion of the primary cell. This intergranular corrosion phenomenon also exists in the ferritic stainless steel mentioned above.Production mode stainless steel pipe can be divided into seamless pipe and welded pipe according to the production mode. Seamless steel pipe can be divided into hot-rolled pipe,Davintel904L stainless steel plate, cold-rolled pipe, cold drawn pipe and pipe. Cold drawing and cold rolling are the secondary processing of steel pipe; Welded pipe is divided into straight seam welded pipe and spiral welded pipe.Davintel,According to different metallographic structure of stainless steel, it is divided into semi Ferritic and semi martensitic stainless steel pipe, martensitic stainless steel pipe, austenitic ferritic stainless steel pipe,For business people, of course, it is better to spend less under feasible conditions. For goods such as stainless steel pipes, we can often see that there will be packaging film bags on them. Although they are not heavy, if there are a large number of single purchases, they will also produce certain economic expenses, but why do many people clearly dislike this thing on stainless steel pipes, But I have to accept it. Next, xincoral Xiaobian will tell you why stainless steel pipes need packaging bags.Austenitic stainless steel can be used to manufacture stainless spring, clock spring and steel wire rope in aviation structure after deformation strengthening. If welding is required after deformation spot welding process and deformation can only be used to increase the tendency of stress corrosionThe best way to improve the quality of stainless steel pipe fittings is to change the process from ingot to billet. Due to the improvement of continuous casting process, this has become a necessary means to improve product quality.

Stainless steel pipes and water transmission equipment for fluid transportation such as water and gas are advanced basic water purification materials in the world. They have strong anti-corrosion performance, which can not be compared with cast iron pipes, carbon steel pipes and plastic pipes.Stainless welded disc (grade I) gb- stainless steel pipe (grade I)Production process of stainless steel pipe A. preparation of round steel; b. Heating; c. Hot rolling perforation; d. Cutting head; e. Pickling; f. Grinding; g．； h. Cold rolling; i. Degreasing; j. Solution heat treatment; k. Straightening; l. Pipe cutting; m. Pickling; n. Finished product inspection.packing,In engineering,DavintelSpecification and thickness of 316 stainless steel pipe, the following methods are often used to prevent intergranular corrosion: reduce the amount of carbon in steel so that the amount of carbon in steel is lower than the saturated solubility of austenite in equilibrium, that is, fundamentally solve the problem of precipitation of chromium carbide (crc) on the grain boundary. Generally, the requirement of intergranular corrosion resistance can be met when the amount of carbon in steel is reduced to less than .%.AUSTENITIC FERRITIC duplex stainless steel. It has the advantages of both austenitic and ferritic stainless steel, but poor plasticity and weldability.Welding, high frequency preheating plus three torch argon arc welding, high frequency preheating plus plasma argon arc welding. The progress of combined welding is very significant. As for the combined welding of steel pipe with high-frequency preheating, the welding operation is complex, and the whole welding is easy to complete automation. This combination is easy to connect with the existing high-frequency welding equipment, with low investment cost and good benefit.

When the stainless steel pipe with solid core welding wire is prefabricated, the welded junction can usually be rotated for welding, and the ventilation is very easy. At this time, the blocking plate is usually used to block both sides of the welded junction in the pipe, and the bottom welding is carried out for the protection of ventilation (see Table ), and the outside is blocked with adhesive cloth.Job descriptionAustenitic stainless steel. It contains more than % chromium, about % nickel and a small amount of molybdenum, titanium, nitrogen and other elements. Good comprehensive performance and resistance to corrosion of various media.According to the steel structure, austenite ferrite ferrite martensite and precipitation hardening note: precipitation hardening (precipitation strengthening): refers to a heat treatment process in which the metal is hardened by the segregation zone of solute atoms in supersaturated solid solution and / or the desolved particles are dispersed in the matrix. For example, austenitic precipitated stainless steel can obtain high strength by precipitation hardening at ~ ℃ or ~ ℃ after solution treatment or cold working. That is, the supersaturated solid solution of some alloys is placed at room temperature or heated to more & amp; gt;& amp; gt;The product quality advantages of continuous casting billet of stainless steel pipe fittings are mainly reflected in that the non grinding rate of the outer surface of the billet except the head and tail section has reached more than %, and the total surface grinding yield has reached %. In order to achieve this goal, it is necessary to refine the molten steel achieve low oxygen and sulfur content, do a good job in the metallurgy of the ladle and tundish, accurately determine the molten steel temperature, and realize no oxidation casting, Further reduce the inclusion content.Davintel,Assembly: the sealing ring shall be correctly installed in the U-groove of the pipe fitting, put the pipe into the socket of the pipe fitting and wait for crimping.Household worries.Household worries.