Impeller protection in order to ensure the operation of the submersible slurry pump, it is necessary to timely adjust the clearance between the impeller and the front guard plate. When adjusting the impeller clearance,Narail Baigang deep well pump, first stop the pump, loosen the bolts pressing the bearing box, loosen the adjusting nuts, make the bearing components move forward,　　In this way, the upper guide housing is installed in turn. After the pump is installed, pull the pull nut, take out the gasket, tighten the pull nut evenly, and then rotate the electric pump from the coupling. The rotation must be uniform.　　Balance of.Thanatpin,　　 If it is found that the impeller is damaged and the liquid supply is insufficient, it is necessary to replace the new impeller in time for use.　　Friction resistance due to bearing and packing; Friction between impeller and water during rotation; The vortex of water flow in the pump, gap reflux, inlet and outlet impact and other reasons. A part of the power must be consumed, so it is impossible for the water pump to completely change the power input by the power machine into effective power, in which the constant active power　　 If the hot water within ℃ is recommended, the hot water pump must be used, and the external tap water shall be connected for cooling during operation,Narail Sewage pump diving, otherwise the motor will not be burned due to too high medium temperature.

　　When the water level reaches, the frequency of the frequency converter drops, and the slurry pump operates at a low speed. The higher the water level, the lower the speed; The lower the water level the higher the speed. At the same time, the circulation in the slag slurry pool is basically unchanged　　For example, /c-ah slurry pump is a small-diameter slurry pump without impeller removal ring. When it is necessary to remove the impeller, we only need to fix the pump shaft rotate the impeller in the opposite direction according to the rotation direction on the pump body, and then the impeller can be easily removed　　The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, we also need to refer to the instructions when disassembling.Welcome calls , the above two cases are the case that the slurry pump does not absorb water. The solutions are also introduced. I believe that people can deal with this problem in time. However, if the problem is serious, you must not adjust it at will. At this time, you should find a professional　　 Then replace the pulley and pump cover plate and tighten the fixing nuts.　　 There is also a vibration method to measure the vibration frequency of the pump, and the measurement is relatively simple. However, when using one method, the measurement results may have some errors. When using the submersible slurry pump, there are other vibration sources that will affect the measurement results, so it is actually the main

　　 Another possibility is that the gas is sucked in when the pump is in use.resources,　　First, let&#;s talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking, the submersible slurry pump is also a vertical slurry pump, because its axis is basically vertical when it works, but it can be completely immersed in water when it runs, so it is a good choice　　 Before using the pump carefully check whether the cable is damaged, whether the fasteners are loose or fall off, and whether the pump is deformed or damaged during transportation storage and installation.　　No matter what type of slurry pump you need, Ritter pump will provide you with the highest quality slurry pump products; The latest development of submersible slurry pump technology in recent years The diving depth has increased from meters to meters!Narail ,　　Under the action of auxiliary devices, it can transport the slurry, and because the sealing device itself is special, it can also ensure the internal and external balance of the submersible slurry pump during transportation, so that the pressure at both ends of the equipment can be balanced during normal use　　During the process,Narail Single stage slurry pump, the equipment must be regularly maintained and overhauled to avoid blockage. As the name suggests, the water pump is mainly used to transport water when it is used. The effect of normal pumps is often better when it is used, but in fact, we use it at ordinary times　　 There may also be mechanical failure of the pump, so that the bore will be 'swept' when the stator and rotor rub against each other, or the impeller will be stuck due to impurities such as water and grass when the pump pumps water