such as serious damage to the bearing of the pump, so that the bore will be 'swept' when the stator and rotor rub against each other, or the impeller will be stuck due to impurities such as water and grass when the pump pumps water Vertical slurry pump is an early product. Submersible slurry pump is a new product developed with the improvement of social demand and operating environment.Kafkana, When the slurry pump operates, it rotates at a high speed, and the components of the slurry pump have a heavy weight. Therefore, once it reverses, the force will directly push the impeller to the outside, and the impeller collides with the sheath and guard plate. If the speed is high, the force ratio is low After the submersible slurry pump leaves the factory,KafkanaQuotation slurry pump, there is generally only outgoing cable, and the user needs to connect it separately during installation. If the connection is wrong, it will seriously affect the normal operation of the pump, so we should follow the correct steps to connect.Rio-Cauto, The mixing impeller and other main flow passage parts are made of high wear-resistant materials, which are wear-resistant, corrosion-resistant, non clogging and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more thorough desilting. No auxiliary vacuum pump is required and the investment is lower. nothing In fact, the impeller clearance of submersible slurry pump is not adjustable for all types of pump, but it is adjustable. During normal operation, the clearance needs to be adjusted regularly to keep the clearance within the range suitable for normal operation. Some corrosive pastes containing crystals can also be transported. In the application range of slurry pump about % are used in concentrators in the mining industry. Due to the poor working conditions of primary ore dressing, different minerals, abrasion
Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point. The fire control cabinet has fault alarm . When a single fire pump is working, it is not easy to be found in time in case of insufficient water source, power circuit failure, etc., resulting in damage to the fire pump. Using the fire control cabinet, the alarm of the control cabinet can remind each However, there is also a disadvantage of using the auxiliary impeller sealing system,KafkanaVortex pump and pipeline pump, that is, it takes some energy on the auxiliary impeller of the submersible slurry pump, which is generally about %. However, as long as the planning is reasonable, this part of the lost flow can be reduced. The slurry pump is mainly applicable to electric power, metallurgy and coalWhere is it, Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop, and tighten the two dust discs and fasten them on the shaft. adjustment selection of pump head: generally, we need to know that submersible pumps generally operate in water. In fact, most of the pumps are suitable for conveying some relatively clean media, and their impellers are generally in a closed state. However, one of the media conveyed by sewage pumps may
The motor is scrapped. Moreover, the installation and use of the pump is troublesome, and the application occasions are subject to many restrictions.Statistics for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places. Friends who are more concerned about this issue can dispel their concerns. The of descending axial force can be used for slurry transportation in power plants hydraulic and other professions; The mechanical seal is tight and reliable, which is mostly used to transport flammable and the leakage probability does not exceed drops /min, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.Kafkana, determination of model: for water pump or pump with physical and chemical medium similar to water, it is necessary to go to the relevant product catalog or sample, and make correction according to the performance table or performance curve of the model to see whether the normal working point falls in the priority working area of the pump. It needs to be replaced in case of damage, swelling and deformation, insufficient spring pressure, breakage, etc. The input quantity is related to many factors such as the rotating speed of the submersible slurry pump, the bearing standard, the continuous working time,KafkanaSubmersible pump can pump sewage, the number of stops and starts of the pump, the surrounding environment and the working temperature. Therefore, it is necessary to gradually accumulate the experience and add smooth oil in a reasonable and timely manner.